393
110 gép:
6.3.9d
► A fűnyíró egység hajtás szíja akkor van helyesen megfeszítve, ha a feszítő rugó (
2
) hosszúsága
135±1 mm
. Ettől
eltérő méret esetén a feszítést az anya (
1
) elforgatásával állítsa be.
6.3.10 FŰNYÍRÓ EGYSÉG - KISZERELÉS A GÉPBŐL
6.3.10a
► A fűnyíró egységet állítsa a legmagasabb helyzetbe, a kart állítsa a 7-es állásba.
► Kissé emelje meg a fűkihordó csatornát (1) és emelje ki a fűnyíró egység keretébe hegesztett két csapszegből. Majd
a csatornát tolja hátra 10 cm-rel, vagy a csatornát vegye ki a gépből a hátsó lapon keresztül.
6.3.10b
► Megfelelő méretű kulccsal forgassa el az anyát (2), hogy a rugó (3) feszülése megszűnjön. Majd vegye le a szíjat (1)
a motor elektromágneses kuplungról.
6.3.10c
► A fűnyíró egység felfüggesztésének a két hátsó csapszegéből (5) húzza ki a rugós sasszeget (
4
). Az első
csapszegnél csavarozza le az anyát (6) és a csapszeget (7) húzza ki. Fogóval húzza ki mindkét csapszeget (
5
).
A mulcsozásra is alkalmas gépek esetén szerelje le a mulcsozó zsalu karjának a gép padlóján túlnyúló részét.
6.3.10d
► A fűnyíró egységet lassan húzza ki valamelyik oldalon gépből.
6.3.11 A KORMÁNYZÁS KARBANTARTÁSA
6.3.11
Rendszeresen ellenőrizze le, hogy a fogas ív és a fogaskerék között nincs-e nagyobb hézag. Ha a hézag nagy, akkor
azt meg kell szüntetni. A hézag megszüntetése (beállítása):
► Hajtsa fel a motorháztetőt.
► Lazítsa meg a két M12 anyát (
1
) a központosító csavaron.
► A központosító hatlapú (2) részét egy megfelelő méretű kulccsal addig fordítsa el, amíg a hézag nem lesz minimális.
► Mindkét M12 anyát (
1
) 35 - 45 Nm-es nyomatékkal húzza meg.
A fenti karbantartás elhanyagolása esetén a kormányzás meghibásodhat.
6.3.12 MENETHAJTÁS ÉKSZÍJ ÁTTÉTELÉNEK AZ ELLENŐRZÉSE ÉS BEÁLLÍTÁSA
6.3.12a
Rendszeresen ellenőrizze le a menethajtás ékszíj áttételének az állapotát és feszességét. A szíj akkor van helyesen
megfeszítve, ha a két szíjtárcsa (1) és (3) közti távolság felénél 4 kP erővel történő megnyomás hatására a szíj
körülbelül 1,5 cm-re hajlik be.
Ha a behajlás ennél nagyobb, akkor a feszességet be kell állítani.
Tételek az ábrán:
(1) Motor ékszíjtárcsa
(2) Vezető tárcsa
(3) Feszítő tárcsa
(4
) Sebességváltó szíjtárcsa
Az erőt szaküzletben vásárolható erőmérővel lehet pontosan mérni.
6.3.12b
A szíj feszítéséhez az anyát (6) addig forgassa, amíg a rugó (5) hossza nem lesz 95 ± 1 mm.
Az ékszíjat ennél jobban ne feszítse meg, mert rövidebb lesz az élettartama és a sebességváltó is meghibásodhat!
6.3.13 ÉKSZÍJ CSERE
A hajtás ékszíj cseréje bonyolult folyamat, ezért ezt a munkát a márkaszerviznél rendelje meg.
6.3.14 KERÉKCSERE
A kerékcsere előtt a géppel vízszintes és szilárd helyen álljon le, állítsa le a motort, majd a kulcsot húzza ki a gyújtáskapcsolóból.
A cserét a következő módon hajtsa végre:
Summary of Contents for OM 105J
