background image

OLIMEX© 2015

AM3352-SOM user's manual

DISCLAIMER

© 2015 Olimex Ltd. Olimex®, logo and combinations thereof, are registered trademarks of Olimex Ltd. Other product
names may be trademarks of others and the rights belong to their respective owners.

The information in this document is provided in connection with Olimex products.  No license, express or implied
or otherwise, to any intellectual property right is granted by this document or in connection with the sale of
Olimex products.

The hardware design of AM3352-SOM development board is considered intellectual property to Olimex. Hardware
schematics are shared with the customers. However, the board layout files are considered copyright material and would
not be shared.

The   hardware   design   of  AM3352-SOM-EVB   development   board   is   considered   open   source   hardware.  The   source
design files are published online and accessible by everyone. 

The software is released under GPL.

It is possible that the pictures in this manual differ from the latest revision of the board. 

The product described in this document is subject to continuous development and improvements. All particulars of the
product and its use contained in this document are given by OLIMEX in good faith. However all warranties implied or
expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This
document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or
damage arising from the use of any information in this document or any error or omission in such information or any
incorrect use of the product.

This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only
and is not considered by OLIMEX to be a finished end-product fit for general consumer use. Persons handling the
product must have electronics training and observe good engineering practice standards. As such, the goods being
provided   are   not   intended   to   be   complete   in   terms   of   required   design-,   marketing-,   and/or   manufacturing-related
protective considerations, including product safety and environmental measures typically found in end products that
incorporate such semiconductor components or circuit boards.

Olimex currently deals with a variety of customers for products, and therefore our arrangement with the user is not
exclusive. Olimex assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein.

THERE IS NO WARRANTY FOR THE DESIGN MATERIALS AND THE COMPONENTS 
USED TO CREATE AM3352-SOM AND AM3352-SOM-EVB. THEY ARE CONSIDERED 
SUITABLE ONLY FOR AM3352-SOM AND AM3352-SOM-EVB, RESPECTIVELY.

Page 2 of 36

Summary of Contents for AM3352-SOM



























Reviews: