background image

Disclaimer

:  

© 2008 Olimex Ltd. All rights reserved. Olimex®, logo and combinations thereof, are registered trademarks of 
Olimex Ltd. Other terms and product names may be trademarks of others. 

The information in this document is provided in connection with Olimex products. No license, express or implied 
or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Olimex 
products.  

Neither the whole nor any part of the information contained in or the product described in this document may be 
adapted or reproduced in any material from except with the prior written permission of the copyright holder. 

The product described in this document is subject to continuous development and improvements. All particulars of 
the product and its use contained in this document are given by OLIMEX in good faith. However all warranties 
implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are 
excluded. 

This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for 
any loss or damage arising from the use of any information in this document or any error or omission in such 
information or any incorrect use of the product. 

Summary of Contents for MOD-RFID125














Reviews: