ENGLISH
EN - 14
3.5 - USE OF THE APPLIANCE
To use the appliance, work as follows.
3.5.a - Appliance switching on/off
In the event that a main switch has been installed on the power line, it must be switched on.
a
. To switch on/off the fan coil/fan radiator, press key
“
”
(T2) for 2 seconds.
b
. The appliance can be switched on or off by pressing key “
B1
” on the remote controller.
All the timers are reset when the appliance is switched off.
The absence of any light signal identifies the ‘stand-by’ status, absence of function.
When the control is set to this mode of operation, it ensures safety against freezing. In the event that am-
bient temperature drops below 5°C, the hot water solenoid valve and the fan motor at minimum speed are
activated, the display shows code “AF”.
3.6 - AUTOMATIC COOLING /HEATING MODE
Setting this type of adjustment allows the control to automatically carry out the selection of cooling or heating
mode, based on the difference between temperature set by the user and ambient temperature.
a
. To activate/deactivate this function, keep the cooling/heating selection key “
B1
” pressed for 10 seconds
until the blue and red symbols (A5) light up alternatively.
This setting is maintained also in the event of power interruption.
b
. Then, ensure that when the set temperature is changed, the unit alternates cooling only (blue indicator
“A5” on), fan (blue and red indicators off) or heating only (red v “A5” on) mode.
c
. Pressing key “
B1
” for 2 seconds allows to cyclically select cooling (blue LED), heating (red LED) or fan
(red LED and blue LED off) mode.
In this mode, read ambient temperature compensation is disabled.
This setting can only be carried out from the panel on board the machine.
3.7 - MANUAL COOLING/ HEATING MODE
From board the machine
a
. To activate/deactivate this function, keep cooling/heating selection key “
T3
” pressed for 10 seconds until
the blue and red symbols (A5) light up alternatively.
This setting is maintained also in the event of power interruption.
b
. Pressing key “
T3
” for 2 seconds allows to cyclically select cooling (blue LED), heating (red LED) or fan
(red LED and blue LED off) mode.
From remote controller
a
. To activate/deactivate this function, press key “
B2
” until the heating only (10) or cooling only (11) symbols
appear on the remote controller
From the remote controller it is not possible to change setting from manual mode to automatic mode.
Summary of Contents for B0872
