Olimpus FLUOVIEW FV500 User Manual Download

Page: 156 / 470

APPLIED OPERATIONS

/Image Acquisition

2-46

Page

Save image.

(Section 2-3-1 in [OPERATION])

Configure the microscope and scan unit.

(Sections 2-2-1-1 & 2-2-1-2 in [OPERATION])

Set the objective magnification.

(Section 2-2-1-4-1 in [OPERATION])

Set the dyeing method.

(Section 2-2-1-1 in [OPERATION])

Set the channel to be acquired.

(Section 2-2-1-4-3 in [OPERATION])

Set the highest scan speed.

(Section 2-2-1-4-4 in [OPERATION])

Perform repeated scanning.

(Section 2-2-1-4-6 in [OPERATION])

Set the XY observation mode.

(Section 2-2-1-4-5 in [OPERATION])

Set the observation range.

(Section 2-2-1-4-8 in [OPERATION])

Set a lower scan speed.

(Section 2-2-1-4-10 in [OPERATION])

Re-adjust the image brightness.

(Section 2-2-1-4-9 in [OPERATION])

Stop repeated scanning.

(Section 2-2-1-4-11 in [OPERATION])

Set the observation mode.

(Section 2-2-2-4-3 in [OPERATION])

Acquire image.

(Section 2-2-2-4-4 in [OPERATION])

Set the range of the cross-section to be

observed (the Z-direction scanning range),

(Section 2-2-2-4-1 in [OPERATION])

Set the numbers of Z-direction steps

and acquired image slices.

(Section 2-2-2-4-2 in [OPERATION])

Adjust the Z-position to observe the

desired cross-section.

(Section 2-2-1-4-7 in [OPERATION])

Adjust the image brightness.

(Section 2-2-1-4-9 in [OPERATION])

Set the zoom ratio to 1X.

(Section 2-2-1-4-2 in [OPERATION])

If the image
does not
become
clean

If the image
becomes
clean

Summary of Contents for FLUOVIEW FV500























































































































































































































































































































































































































































































Search results

Summary of Contents for FLUOVIEW FV500

Reviews:

Related manuals for FLUOVIEW FV500

Brands by name

Popular brands

Olimpus FLUOVIEW FV500, User Manual

Search results

Summary of Contents for FLUOVIEW FV500

Reviews:

Related manuals for FLUOVIEW FV500

Brands by name

Popular brands