Olimpus FLUOVIEW FV500 User Manual Download | Manualshive

Page: 465 / 470

background image

TROUBLESHOOTING GUIDE

1-3

Page

Phenomenon

Cause

Treatment

Manual Ref. Pages

5. Image looks poor.

The fluorescent dye does not
match the barrier filter.

Select the barrier filter
matching the fluorescent
dye.
Change the ND filters by
reading 1-2-7, “Selecting the
ND Filter” in OPERATION
INSTRUCTIONS.

1-2-7, OPERATION
INSTRUCTIONS

The excitation light is weak. Increase the transmittance

of the ND filter.

1-2-7, OPERATION
INSTRUCTIONS

The installation location is
subject to large vibrations.

Consult Olympus.

-

6. Image is irregularly

blurred or the
brightness is uneven.

The specimen is tilted.

Set the specimen
horizontally.

Instruction manual
of microscope

7. Image is flared.

Non-fluorescent glass is not
used.

Use non-fluorescent glass.

-

The cover glass thickness is
not optimum.

Use a cover glass with a
thickness of 0.17 mm.

-

The specimen is over-
stained.

Stain it properly again or
increase the OFFSET value.

2-2-1-4-9,
OPERATION
INSTRUCTIONS

8. Circular flare is

observed at the center
of image.

The excitation wavelength
does not match the barrier
filter type or the barrier filter
is not used.

Select suitable barrier filter
for the excitation length.

1-2-6 & 1-3-2-4,
OPERATION
INSTRUCTIONS

9. Image is blurred or out

of focus.

The focusing is not correct. Adjust focusing with visual

observation.

Instruction manual
of microscope

10. Image is dark and

noisy.

The fluorescent dye is pale. Apply optimum fluorescent

dye.

-

The pinhole diameter is too
small.

Adjust to an optimum size.

1-3-2-5,
OPERATION
INSTRUCTIONS

The HV of photomultiplier
tube exceeds 800.

Set HV at no more than 800.
If the image is still dark,
adjust GAIN.

2-2-1-4-9,
OPERATION
INSTRUCTIONS

The scan speed is too high. Decrease the scan speed or

integrate the image.

1-2-8-9 & 2-2-1-6,
OPERATION
INSTRUCTIONS

The excitation light is weak. Increase the transmittance

of the ND filter.

1-2-7, 1-3-2-4 & 2-
2-1-4-10,
OPERATION
INSTRUCTIONS

11. The position

reproduction of the Z-
motor is poor.

The Z-position fluctuates
because the coarse
movement knob of
microscope is too light.

Make the microscope’s
coarse movement knob
heavier by turning the
microscope’s rotation
tension adjustment ring.

Instruction manual
of microscope

«
...
463
464
465
466
467
...
»

Summary of Contents for FLUOVIEW FV500























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for FLUOVIEW FV500

Brand: OPTIKA MICROSCOPES Pages: 44

Brand: Labomed Pages: 12

Brand: STEINDORFF Pages: 14

Brand: National Pages: 7

Brand: Nikon Pages: 124

Brand: Turku Bioscience Pages: 16

Brand: Zeiss Pages: 40

Brand: Zeiss Pages: 210

Brand: Zeiss Pages: 140

Brand: 3B SCIENTIFIC PHYSICS Pages: 24

Transillumination top 450 mot.

Brand: Zeiss Pages: 18

Brand: Zeiss Pages: 4

Brand: 4Deep Pages: 25

Brand: Konig Pages: 24

Brand: HomeScienceTools Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands