background image

E-1

INSTALLATION MANUAL

d-Color MF 552 plus/d-Color MF 452 plus/

d-Color MF 362 plus/d-Color MF 282 plus/d-Color MF 222 plus

<Important>
Be sure to correctly follow the procedures in order as explained in this Installation Manual.
If you do not follow the procedure in order, the image trouble may occur.

©

 Olivetti S.p.A

I. Outline of installation procedures (d-Color MF 552 plus/d-Color MF 452 plus)

When installing the machine and associated options as a system, follow the order shown on the upper.

Caution:

    • For the detailed installation procedures for each 

option, follow the instructions given in the corre-
sponding installation manual and perform the 
procedures correctly. (Optional devices must be 
installed after completing the main unit installa-
tion.)

    • Once the Power Switch is turned ON, do not 

turn OFF it until the installation work has been 
completed.

    • When placing the machine on the floor, make 

sure to use the paper feed cabinet to secure the 
performance and the quality of the product.

    • Lifting the machine in an awkward position or 

transporting it in a poorly balanced position 
could result in personal injury. When transport-

ing the machine, assign an adequate number of 
persons to the job and ensure that each person 
can take a good position of not being exces-
sively loaded. 
(mass: approx. 101 kg (222-11/16 lb))

AU-102

WT-506

AU-201

*2

SP-501

PC-110

OT-506

Machine

PC-210

MK-730

FS-534

FS-533

PK-519

MK-734

KH-102

PC-410

TK-101

AU-201

*1

MK-735

HT-509

ZU-606

*4

FS-535

*4

JS-506

LU-204

LU-301

PK-520

SD-511

JS-602

*4

PI-505

*4

PK-521

*4

SD-512

*4

UK-204

*3

Electronic system options

EK-606

*3

EK-607

*3

SC-508

*3

FK-511

VI-506

IC-414

 Electronic system options

*1

: When installing the AU-201 with MK-735

*2

: When installing the AU-201 without MK-735

*3

: No particular order in installation procedures.

*4

: Unable to be installed in d-Color MF 452 plus.

UK-208

*3

KP-101

A2XKIXC001DA

Applied Machines: d-Color MF 552 plus/d-Color MF 452 plus/d-Color MF 362 plus/

d-Color MF 282 plus/d-Color MF 222 plus

Y115290-3                                                                                             

    

                  

 

                     Installation Manual

Y115290-3                                                                                             

    

                  

 

                     Installation Manual

Summary of Contents for d-COLOR MF222plus































Reviews: