Olivetti d-COPIA3003MF Operation Manual Download | Manualshive

Page: 42 / 440

background image

2

Preparation before Use

2-7

Power Off Timer

If the machine is not used while in sleep mode, the power automatically turns off. The Power Off Timer is used to set
the time until the power turns off. The factory setting for the time until the power turns off is 1 hour.

In case of not using the machine for a extended period of time

CAUTION:

If this machine will be left unused for an extended period (e.g. overnight), turn it off at the power

switch. If the machine will not be used for an even longer period of time (e.g. vacation), remove the power
plug from the outlet as a safety precaution. If using the machine with fax, note that turning the machine off at
the power switch disables fax transmission and reception.

CAUTION:

Remove paper from the cassettes and seal it in the paper storage bag to protect it from humidity.

Sleep

When the set time (factory setting is 1 minute) elapses after the machine is last used, the machine automatically
enters sleep mode. The message display backlight and lights turn off to minimize power consumption. This status is
referred to as Sleep. When in the Sleep state, "Sleeping" appears in the message display.

If print data is received during Sleep, the print job is performed while the Message Display remains unlit.

If you are using the machine with fax, received fax data is printed out while the operation panel also remains unlit.

To use the machine, press the any key on the operation panel. The machine will be ready to operate in about 15
seconds.

Note that ambient environmental conditions, such as ventilation, may cause the machine to respond more slowly.

«
...
40
41
42
43
44
...
»

Summary of Contents for d-COPIA3003MF

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-COPIA3003MF

Brand: Fiery Pages: 114

Brand: Olivetti Pages: 78

image RUNNER 3045

Brand: Canon Pages: 216

Brand: Lanier Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands