OLT CB128-AK-METAL Assembly Manual Download | Manualshive

Page: 4 / 45

background image

Thank you for purchasing our 12x8 Cabana Garden Shed.
Please take the time to identify all the parts prior to assembly.

Note:

All Trim, Facia and Bottom Skirting pieces will be positioned rough face out when installed.

1. Floor Section

Floors

3 - 45 1/2” x 75” - Floor Joist Frames - Large
3 - 45 1/2” x 21” - Floor Joist Frames - Small
6 - 1 1/2” x 3 1/2” x 71 7/8” - Center Floor Joists - Unattached
10 - 1 1/2” x 3 1/2” x 68 3/16” - Floor Runners
3 - 45 3/8” x 74 7/8” - Plywood Floor - Large
3 - 45 3/8” x 20 7/8” - Plywood Floor - Small

2. Wall Section

Main Wall Panels

7 - 45 1/2” x 75” - Solid Wall Panels
7 - 1 1/2” x 2 1/2” x 45 1/2” - Bottom Wall Plates
2 - 45 1/2” x 75” - Window Wall Panels
1 - 12” x 73” - Narrow Wall Panel

Door Header & Jamb

1 - 1 1/2” x 3 1/2” x 73” - Vertical Door Jamb

1 - 2” x 3 1/2” x 45 1/2” - Door Header (Dado cut on edge)

Top Wall Plates & Gables

6 - 3/4” x 2 1/2” x 32” - Side Top Plates
(4 pieces angle cut on end, 2 piece straight cut both ends)
4 - 3/4” x 2 1/2” x 65 3/4” - Front & Rear Top Plates (angle cut edge)
4 - Gable Half Walls - Triangular Shaped

3. Rafter and Roof Section

Rafter Assembly

2 - 3/4” x 4 1/2” x 84” - Roof Ridge Boards
2 - 3/4” x 4 1/2” x 52 1/2” - Roof Ridge Boards
18 - 1 1/2” x 3 1/2” x 56 1/2” - Roof Rafters
4 - 1/2” x 4 1/2” x 68 1/4” - Soffits
3 - 3/4” x 3 1/2” x 72” - Roof Gussets (angle cut on ends)

Roof

16 - 3/4” x 3 1/2” x 49 1/4” Roof Batten (outside)
8 - 3/4” x 3 1/2” x 45 1/2” Roof Batten (middle)
12 - 3/4” x 1 1/2” x 14 1/8” - Batten Spacers
8 - 61” long x 39” wide Metal Roof Panels
3 - 13”w x 60” Metal Ridge Cap
Several Strips of Foam Enclosures for Metal Roof Ends

4. Trim & Miscellaneous Section

Outer Wall Trim

10 - 3/4” x 4 1/2” x 45 1/4” - Bottom Skirting (Bevel)
4 - 7/8” x 2 1/2” x 75” - Filler Trim
5 - 3/4” x 1 1/2” x 45 1/4” - Top Wall Trim (Bevel)
4 - 3/4” x 4 1/2” x 45 1/4” - Horizontal Gable Trim (Bevel)
4 - 1/2” x 3 1/2” x 79” - Corner Trim
4 - 1/2” x 5 1/2” x 82” - Wide Corner Trim
2 - 1/2” x 2 1/2” x 79” - Rear Wall Narrow Trim
2 - 1/2” x 2 1/2” x 77 1/2” - Side Wall Narrow Trim

Facia Trim

4 - 3/4” x 2 1/2” x 51” - Facia Nailing Strips
4 - 3/4” x 3 1/2” x 58” - Side Facia (Angle Cut, 2 right, 2 left)
4 - 3/4” x 3 1/2” x 71 3/4” - Front and Rear Facia
2 - Pentagon Facia Plate - For Side Facia Peaks
2 - Horizontal Gable Trim Detail Plates - 4 1/2” high
2 - Facia Detail Plates - 3 1/2” high

21-22

Steps

Steps

24-27

Steps

39-55

56-62

63-67

Steps

13-20

1-12

28-38

Parts List - Pages 2 and 3

Continued on next page

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com sales@outdoorlivingtoday.com

Page 4

«
...
2
3
4
5
6
...
»

Summary of Contents for CB128-AK-METAL














































Reviews:

No comments

Related manuals for CB128-AK-METAL

Palmako Sally FR44-3838-1

Brand: Lemeks Pages: 54

Brand: Grosfillex Pages: 64

Brand: Oakville Pages: 45

Brand: Palmako Pages: 27

Skylight Shed 6x8

Brand: Palram Pages: 64

Brand: Palmako Pages: 105

Brand: Palmako Pages: 58

Brand: Palmako Pages: 53

Brand: Palmako Pages: 52

Brand: Karibu Pages: 6

Brand: Palmako Pages: 55

Brand: Biohort Pages: 40

Brand: Keter Pages: 17

Brand: Keter Pages: 34

Brand: Keter Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands