background image

 

 

 

 

ENABLE

SIREN            1

With  the  numeric keypad and the ‘ENTER’ key select the required SIREN 
output. The  Display  shows: 

And  the  siren  output  is  activated.

SIREN OUTPUT  1

IS ENABLED

ENABLE

RELAYS OF UNIT   1

With the numeric keypad and the ‘ENTER’ key select the required BS-117 
device. The  Display  show

s:

 

If  ‘ENTER’  is  pressed  then  all  the  relays  of  the  BS-117  are  activated.

1234567890123456

ENABLE

RELAY  (1/64)    01

With  the  numeric  keypad  and  the  ‘ENTER’  key  select  a  specific  relay  (e.g 
relay1) of  the  selected  BS-117 device. The  Display  shows: 

If  ‘ENTER’ is  pressed  again  then  the  chosen  relay  is  activated.

1234567890123456

7.6 History record deletion

The  sixth  selection  of  the  technicians  menu  is 

If ‘ENTER’   is   pressed   then   the   history   record   of   the   system   is deleted.   All ALARM and 
FAULT  events  are  written  in  this  record.

DELETE

HISTORY FILE

7.7 Automatic unit recognition

The  seventh  selection  in  the  technicians  menu  is 

If  ‘ENTER’  is  pressed  the  SETUP procedure  described  in  section  5  commences.

AUTOMATIC

UNIT DETECTION

7.8 Setting the user code.

 

The eight selection in the technicians menu is

  

If  we  press  ‘ENTER’  the display shows : 

Using   the   numeric   keypad   enter   the   required 4-digit code   that   will   be   used   as   a user 
access code. The default  user  code  set  is  “0000”.

SET

USER CODE

ENTER YOUR CODE

0000

20 

from

 21

921116000

Date

File

Code

Page

921116000_09_016

13/03/2013

Summary of Contents for BS-116






















Reviews: