11-4-2017
22
921468001_09_015
SILENT ALARM. The code activates the silent alarm. When the user enters the code, the panel will
disarm (if the panel is armed) and will remain in idle state (the siren will not sound, and the alarm leds
will be off). The panel will call or send a message via BS-465 or BS-464 to the selected telephone
numbers.
General settings
From the
«TECHNICIAN MENU» if we select «SETTINGS» we see:
From this menu we can adjust all the general settings of the panel.
«ENTRANCE TIME». This is the time that the zones delay to give an
alarm. This is valid only for zones that have been programmed as
zones with delay. By pressing (*) a new screen is shown and the
current entrance delay is shown (30) in seconds. Enter the new time
(05-99 2 digits are mandatory) i.e. 0 and 9 for 9 seconds. The
system stores the value and returns to the menu
«SETTINGS».
«EXIT TIME». Is the time from when the arming password is entered
until the actual arming of the system. Pressing (*) reveals a new
screen where the current exit time is shown. By default it is 45
seconds. We enter the new required exit time with 2 digit numbers
(05-99 2 digits are mandatory) i.e. 6 and 0 for 60 seconds. The
system stores the value and returns to the menu
«SETTINGS».
«ALARM TIME». Is the time that the siren is sounded. This time
counts from the instance that all activation devices have stopped
activating the panel. Select 1 or 2 minutes, press (*). The system
stores the value and returns to the menu
«SETTINGS».
«EXTRA EXIT TIME.» Is the time that is added to the exit time when the system is activated with a
password which has an additional delay or by a zone with delay.
«SECTIONS EXIT TIME». With this selection if we will have an exit time for the sections (A, B, C). We
must reply YES or NO for each subsection.
«ENTRANCE DELAY BEEPS.» Select if the built-in buzzer will sound during the entry time.
«EXIT DELAY BEEPS.» Select if the built-in buzzer will sound during the exit time.
«BEEP PARTIALLY ARMED.» Select if the built-in buzzer will sound during the exit time in case of a
partial arming of the system (section arming
Α, Β or C).
«BEEP PARTIALLY ARMED» Select if the system can be armed without a password, with the use of
the keys A. B. C. ABC. The selection only affects the arming, for the disarming a password is always
required.
«ARMED SYS INDICATORS». We have 2 selections «OFF» or «ON». It places in the according state
the 4 indication LEDs when the panel is armed. The indicators are lit when the panel is disarmed.
«IDLE BACKLIGHT MODE» This option regards the illumination of the display and the keypads during
the idle state of the system. The idle state is the state where there is not alarm and no key has been
pressed for 30 seconds. We have 3 options. ALWAYS OFF, ONLY WHEN DISARMED which means
off in an armed system and on in a disarmed system and ALWAYS ON.
«DOUBLE BUTTON PANIC» We select if a panic signal alarm can be issued from the keyboard. If we
select YES and we simultaneous press for two seconds the keys C and ABC then a panel alarm will
be produced.
«RECORD OUTPUTS EVENT». We select if the state of the outputs will be logged as individual
events (
Ρ1, Ρ2, Ρ3 and RELAY).
______SETTINGS______
ENTRANCE TIME
EXIT TIME
ALARM TIME
EXTRA EXIT TIME
SECTIONS EXIT TIME
ENTRANCE DELAY BEEPS
EXIT DELAY BEEPS
BEEP PARTIALLY ARMED
ARM WITHOUT CODE
ARMED SYS INDICATORS
IDLE BACKLIGHT MODE
DOUBLE BUTTON PANIC
RECORD OUTPUTS EVENT
AUTOMATIC BYPASS
REMOTECONTROL ACTION
ANNUAL CHECK WARNING
Summary of Contents for BS-468
Page 1: ...BURGLAR ALARM PANEL BS 468...
