olympia electronics BS-812/A Manual Download

Page: 8 / 10

Page 8 from 10

(The following procedure must be done with the
main power supply isolated)

Retaining screw

entrance

Retaining screw
entrance

Alignment vial

Pre-etched entrance for the connection cable

(must be removed before thermostat’s installation)

Photo 1

Photo 2

Photo 3

Photo 4

Mounting screws

Installation procedure

1 To install the device, use a flat blade screwdriver to
pry up the cover, with the same width as the plastic
opening (photo 2).

2 Unscrew the retaining screws and remove the
plastic cover containing the keys (photo 3).

3 Use the supplied support screws and plugs after
opening the required holes on the mounting surface
(photo 1). Install the base and align using the built-in
alignment vial. Tighten the retaining screws.

4 Press and remove the pre-etched cable entry
(photo 1). Perform the connections as shown in
the diagrams on page 8.

THE NEUTRAL IS NOT CONNECTED.

5 Reinstall with care the plastic with the keys and
fasten the mounting screws. Maximum tightening
torque 0,5 N*m.

6 To activate the device remove the battery
separator (photo 4).

7 Reinstall the plastic cover and press gently until it
snaps into position. The unit is ready to operate.

940812001_09_001

Summary of Contents for BS-812/A











Search results

Summary of Contents for BS-812/A

Reviews:

Related manuals for BS-812/A

Brands by name

Popular brands

olympia electronics BS-812/A, Manual

Search results

Summary of Contents for BS-812/A

Reviews:

Related manuals for BS-812/A

Brands by name

Popular brands