Page
4
from
11
Which ever key is pressed after this will
show the same message on the screen
.
All other function are executed normally.
To unlock the keypad follow the same
procedure and the screen will show the
message .
6. SETTING THE TIME AND DATE
(the
thermostat is in the OFF state).
To enter time adjustment mode press the
key for 3" as mentioned in paragraph 1.
The backlight will be activated and the
lower section of the screen will flash the
message
(
Set
Time). After that press
briefly the key and the hours indicators
will start to blink. Use the keys to
set the correct time. Pressing the key
will cause the minutes indicators to blink
and with the keys change to the
correct value. Pressing again the key
we can adjust consecutively the year,
month and date. You can see that the day
names are changed automatically
depending on the year, month and date.
In
normal operation the clock has leap year
and daylight savings time correction.
7.
SETTING THE DAILY PROGRAM.
(
the thermostat is in the OFF state
).
If immediately after entering the MENU
parameters we press the key then the
blinking message (Day) will be shown
on the bottom of the screen and the word
DAY
on the top right.
By pressing the
key
the message
(
Program 1) is
shown in place of the message
.
In the center of the screen and if
programming is done for the first time we
can see the message . By pressing the
key the hours indicators blink and we
can alter the setting by using the
keys .By pressing the key we
can alter the minutes and the required
temperature.
With the key we can
return to the initial position with the
blinking .
With consecutive presses of the
key we can select the remaining
programs of the 24 hour cycle (10 in total)
and can set the required time periods and
temperatures as described above.
Please
note the for every program we define only
the start time since the end time is the start
time of the next program
.
For example, if we
require a temperature of
23.0 º
C
from
14
:
00
to
18
:00 in program 1 we will set the
start time
14
:00
at
23.0 º
C
and the start time
of the second program
18
:00
with the
required temperature.
The 24 hour time
base starts at
00
:00 and ends at
23
:
59'
.
The start time of the next program must also
be bigger than the start time of the previous
.
If no more changes are required and when
the program indicator is blinking (e.i ) we
can press the key to store all the
changes and the screen will show the
message .
The programs that have
not been adjusted are not taken into
account.
8.
ADJUSTING SETTINGS FOR THE
WEEKLY PROGRAM.
(
the thermostat in in
the OFF state
).
If immediately after entering the MENU we
press the key for 2 times the
message (7days) will be shown on the
bottom of the screen and the word
WEEK
on the top right
.
On the top left of the screen
there is the message
ΜΟ
(
Monday) that
shows the day that corresponds to the
programming that follows.
By pressing
again the key the screen shows a
blinking that determines the first
program of Monday of the weekly program.
The remaining procedure is as described in
paragraph 7(setting the daily program).
Finishing the programming of the first day if
we press the key while the program
number is blinking (e.i ) will show the
blinking message
.
With the key
we can select the day for which we want the
alter the program as described above.
If no
other changes are required then press the
key to save the setting to memory. The
screen will show the message .
It is
stressed that at least one program must be
adjusted for every day else the factory
default temperature of
23.0 º
C will be used
for all the 24 hour base
.
9
.
SELECTING THE UPPER AND LOWER
L I M I T S O F T H E M A N U A L
TEMPERATURE ADJUSTMENT
(
the
thermostat is in the OFF state)
.
After entering the MENU and by
consecutive presses of the key the
message (High Temperature Limit) will
MENU
ENTER
ESC
ESC
940818000
_09_00
4
MENU
ENTER
MENU
ENTER
MENU
ENTER
MENU
ENTER
ESC
ESC
