background image

Page

 

13 from

 

13

940851000

_09_001

Olympia Electronics guarantees the quality, condition and operation of the goods. The 
period of warranty is specified in the official catalogue of Olympia Electronics and also 
in the technical leaflet, which accompanies each product. This warranty ceases to 
exist  if  the  buyer  does  not  follow  the  technical  instructions  included  in  official 
documents given by Olympia Electronics or if the buyer modifies the goods provided 
or has any repairs or re-setting done by a third party, unless Olympia Electronics has 
fully agreed to them in writing. 

Products that have been damaged can be returned to 

the premises of our company for repair or replacement, as long as the warranty period 
is valid.

 Olympia Electronics reserves the right to repair or to replace the returned 

goods and to or not charge the buyer depending on the reason of defection. Olympia 
Electronics reserves the right to charge or not the buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr
info@olympia-electronics.gr

TECHNICAL CHARACTERISTICS

POWERED BY

2

  

Alkaline

 ΑΑ

BS-850/T - BS-851/T

BS-850/R - BS-851/R

MODEL

220 - 240V AC / 50-60Hz

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

TYPICAL WEIGHT

GUARANTEE

MEASURING RANGE

OPEN RELAY CONTACT

DEGREES OF COVER PROTECTION

 

PRODUCED IN ACCORDANCE WITH

2x

5Α - 250

V AC1

o

0.0 

to

 99.9 

C

EN 61000-6-1, EN 61000-6-3, EN 60730-1, EN 60730-2-9

o

5 to 35  C

10 -

 90% RH 

2 years

121.5 x 27.3 x 81.3 mm

IP20

175 gr. (with batteries)

200

 

gr

.

o

-10 to 50  C

10 -

 9

5

% RH 

120 x 34 x 80 mm 

-

CONSUMPTION

1.9VA

WARRANTY

WARRANTY

-

COMMUNICATION FREQUENCY

869,75

MHz

TEMPERATURE SELECTION RANGE

o

6.0 

to

 30.0 

C

-

-

Summary of Contents for BS-850/R














Reviews: