Page
1 from
4
923
579
00
0
_09_0
0
3
GENERAL
These luminaires are used in places where
emergency luminaires are needed.
E a c h l u m i n a i r e m u s t b e p e r m a n e n t l y
connected to mains power supply
.
In normal
operation (L1 connected to L) the led strip
lights and the battery is charging. In case of
a mains power supply failure the luminaire will
light the led strip automatically in emergency
mode (powered by its battery). When the
mains power supply is restored the device
turns to normal operation.
OPERATION
Battery Charging
The battery charging is completely controlled
.
In this case, the best possible battery
maintenance is
achieved
,
as well as the
elongation of its duration
.
When the battery
has completely charged
,
it charges with a
maintenance current.
Battery Cut-off
The luminaire enters in this operation when
the mains power supply fails
and battery has
lost its energy
.
During this operation the
luminaire enters the idle state
and battery
consumption is negligible, in order to be
protected from deep discharge.
Manual
Test
This test can be done by placing the test card
on the side of the indications (page 4) and
remove it instantly. An operation test is initiated
and the light source and the emergency circuit
of the device is monitored. The manual test can
be conducted only if the mains power supply
and the battery is connected. During this test
period all indication LEDs are OFF.
Automatic Operational Test
This test includes all the operations that provide
the manual test and is conducted automatically
every 15 days. In order to be performed, the
mains power supply and the battery should be
connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the device’s back up operation
and emergency duration. This test is conducted
automatically every 6 months
.
In order to be
performed, the mains power supply and the
battery should be connected and fully charged
.
If the battery is not fully charged
,
the test is
postponed
until the battery is completely
charged. If during this test, the autonomy is less
than nominal, then the battery fault led turned
on continuously and the battery must be
replaced.
Congratulations for your selection to buy this product.
Olympia Electronics - European manufacturers
.
220-240V AC/50-60Hz
18
0 min
90 min
11550gr
11730gr
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES (Ni-Cd)
CHARGING TIME
INDICATIONS
-
CONTROLS
BATTERY PROTECTION
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
LIGHT SOURCE INTENSITY (230V AC/emerg.)
ILLUMINATION SOURCE
24 h
Charge LED, Lamp Fault LED, Battery LED
From overcharge and deep discharge
White LEDs
o
5 to 40 C
Up to 95%
3 years
(1
year for the batteries
)
Painted steel plate (RAL 7036), Bayblend FR3010
,
transparent
polycarbonate
IP 65
EN 60598-1, EN 60598-2-22
, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
, EN 1838
740 x 400 x 185 mm
2x4.8V/1.5Ah
2x4.8V/3Ah
2x9W / 2x9.5VA - PF: 0.95/230V
2x680lm / 2x340lm
WATERPROOF SELF TESTING MAINTAINED EMERGENCY LED LUMINAIRES
GR-579/L/90/WP
GR-579/L/180/WP
TECHNICAL CHARACTERISTICS
(
for LED MODULE Specs. see page 4
)
High Quality European based Manufacturers
