‘’ SLIM LIGHT ‘’ SERIES FOR MAINTAINED / NON-MAINTAINED
(OPTIONAL) LUMINAIRE
GENERAL
Charging the Battery
The
of this type cover
standard
functionality in security lights, for professional
or household use.
They have features such as:
1. Change function from
to
or vice versa, whenever
desired.
2. Light sensor to select the activation or not
the l
if there is adequate
lighting in the area.
3.
(with remote
).
4. Possibility of remote control
these
functions and additional functions are
analyzed on page 3.
T h e
m u s t b e p e r m a n e n t l y
connected to the mains
. During
normal operation
charg
the battery and
lights the LED lighting (
mode). In
a n y p o w e r f a i l u r e t h e l
i s
automatically switched to
mode,
lighting the LED lighting
battery.
When
returns to normal operation.
The
battery is fully controlled
by the
to achieve optimal battery
maintenance, and prolong
life. When the
battery is fully charged, the charging current is
limited
maintenance.
luminaires
the
maintained
non-maintained
of
uminaire, when it is connected to the
mains power supply,
Dimming control
control
for
l u m i n a i r e
power supply
it
es
maintained
u m i n a i r e
emergency
from the
the mains power supply is restored the
unit
charging of the
luminaire
ed
for
The functions 1,2 and 3 may be
using the TEST button as explained on page
3.
implemented
Battery
Manual
Automatic
Automatic
Backup Status Operation
cut off
Test
LED Test
duration test
The
this state when the mains
is interrupted and the battery has
lost all its energy. The consumption of all
lighting circuits is limited to the minimum
needed to protect the battery from deep
discharge.
Manual
is performed by pressing the
Test button
check the LED lighting and the
driv
circuit . To
the
should be
and the battery
.
During the test
LED
.
includes
manual
but
automatically every 15 days. To
the
should be
and the battery
measure
the
autonomy of the emergency operation of the
device. This
is performed automatically
every 6 months. To
the
should be
and the battery
and
f u l l y c h a r g e d , o t h e r w i s e t h e c h e c k i s
until the battery is fully charged.
The
of battery life in
mode
is
that specified in the table above.
During the backup operation
.
luminaire enters
power supply
testing
to
ing
perform this operation,
unit
connected to the mains power
supply
must be enabled
the orange
blinks
It
all
tests
is conducted
perform this
operation,
unit
connected to the
mains power supply
must be
enabled.
The automatic duration test
s
test
perform this operation,
unit
connected to the mains power
supply
must be enabled
postponed
duration
emergency
at least
an LED test is
also performed
GR-2000
923200000_09_003
Page 1 from 4
Bayblend F 3010 transparent polycarbonate
R
,
TECHNICAL CHARACTERISTICS
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
CONSTRUCTION MATERIALS
TYPICAL WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERIES Ni-Cd
(
)
CHARGING TIME
INDICATIONS CONTROLS
-
BATTERY PROTECTION
AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
ILLUMINATION SOURCE INTENSITY
ILLUMINATION SOURCE
24h
Charge (green), lamp fault (red), fault (orange) indication LED TEST button
,
From overcharge and full discharge
IP 40
0 to 40 C
o
Up to 95%
3 years
year for the battery
(1
)
270 x 100 x 25 mm
220-240V AC/50-60Hz
3.6V/1Ah
4W
3-7 hours depending on the illumination adjustment of the LED’s
110lm (230V AC) / 110lm (emergency)
White LED’s
340gr.
S A A R
RT
CE
CERTIFICATE
VALID SYSTEM
EN ISO 9001 : 2008
EN 60598-1, EN 60598-2-22, ÅÍ 55015, ÅÍ 61547, ÅÍ 61000-3-2, ÅÍ 61000-3-3
