background image

Page 3

 

        

IMPORTANT SAFETY INFORMATION

Assembly Precautions

1.

  Assemble only according to these instructions.

Improper assembly can create hazards.   

 

2.  Wear 

ANSI-approved safety goggles and

heavy-duty work gloves during assembl

y. 

 

3.  Keep assembly area clean and well lit.

4.

  Keep bystanders out of the area during assembly.

 

5.

  Do not assemble when tired or when under the

influence of alcohol, drugs or medication. 

6.  Weight capacity and other product capabilities apply

to properly and completely assembled product only. 

7.  Assemble on a flat, level, hard and smooth surface

capable of safely supporting a fully loaded Cart. 

Use Precautions

TO PREVENT SERIOUS INJURY AND DEATH FROM TIPPING:

1.

 

DO NOT SIT, STAND OR CLIMB ON THIS ITEM. 

2.  This product is not a toy nor a toy chest.

Do not allow children to play with or near this item.  

 

3. 

Do not exceed weight capacities, evenly

distributed from bottom up.   

 

 

 

Be aware of dynamic loading!

  

Sudden load movement may briefly create

excess load causing product failure. 

 

 

4.

  Do not open more than one Drawer at once.

Lid must be open for Drawers to be unlocked. 

5.

  Close Lid to lock all Drawers, then lock

Lid with Key before moving. 

6.  Use only on a flat, level, hard and smooth surface

capable of safely supporting a fully loaded Cart.

Do not roll Cart over concrete seams

or other rough/uneven surfaces. 

7.  Do not lift using handle(s).

Do not lift while loaded.  

 

8.  Lock Swivel Casters after moving.

9.  Do not mount on truck bed or

any other moving object. 

10.

 Use as intended only.

11.

  Inspect before every use;

Do not use if parts are loose or damaged. 

 

12.

 Maintain product labels and nameplates.

These carry important safety information.

If unreadable or missing, contact

Olympia-Tools

 for a replacement. 

OLYMPIA TOOLS INTERNATIONAL, INC.

Tel. 626-336-4999 / Fax. 626-336-489 / Web. www.olympiatools.com

Summary of Contents for 84-956









Reviews: