Symptoms
Possible Cause
Solution
Ref. in Manual
6. Printing
The characters that are printed
do not correspond to the keys
that are pressed.
* The printwheel is not set
properly, or is not installed.
(The front plate is positioned
incorrectly.)
Reassemble,
replace, or
press the
CODE+W key.
Adjust the
positions.
Ref. to operating
instructions
4.4.2, 5.6
* The home position for the
selection motor is not set
correctly.
Adjust the
setting.
3.3, 4.4.2, 5.6
* The hammer position is
incorrect.
Adjust the
positions.
3.4, 4.4.3, 5.6
* The wrong ROM (control
PCB:999-32300), program
(CPU for control
PCB:999-35810), country
setting, or printwheel is being
used.
Reassemble,
adjust, or
replace.
3.6, 5.2
The top and bottom halves of
characters differ in intensity or
are missing altogether.
* The ribbon base stopper,
adjustment plate, or rail slide
is positioned incorrectly.
Adjust the
positions.
4.4.4, 4.4.5,
5.5,5.6
* The ribbon cassette is used
up.
Replace.
Ref. to operating
instructions
7. Correction
*
When making corrections, either
the ribbon cassette base does
not lift up or the correction is not
made.
The connector (CN203) is not
connected.
Connect the
connector.
3.3, 3.6, 5.6
* The correction tape is not
installed.
Install the
correction
tape.
Ref. to operating
instructions
* Either the hammer position or
the home position for the
selection motor is incorrect.
Adjust the
positions.
4.4.2, 4.4.3, 5.6
* The correct cam, lift pin, or
drive ratchet has failed.
Replace. 4.4.5,
5.5
* The ribbon base stopper,
adjustment plate, or rail slide
is positioned incorrectly.
Adjust the
positions.
4.4.4, 4.4.5,
5.5, 5.6
* The ribbon motor has failed. Replace.
3.3, 5.6
* IC (CPU, ROM, gate array,
etc.) or TRA203 has failed.
Replace. 3.6,
5.2
* The control PCB has failed. Replace.
3.6, 5.2
8-3
Summary of Contents for Carrera De Luxe MD
