background image

 

 

www.microscopenet.com

 

 

- 16 - 

3) 

Raise the condenser till the top lens is close to the opening of stage. Place a drop of 
immersion oil on the top of the lens of the condenser.

 

4) 

Place the slide on the stage. Raise the condenser and let the oil drop 
contact the bottom of the slide. If air bubbles exist in the oil, clean the 
oil from the condenser lens and bottom of slide with a camera 
cleaning paper and repeat the procedures.

 

 

5) 

Follow the procedures in this manual to bring the sample on slide in 
focus and observe.

 

6) 

When using the 100X oil darkfield objective, you will need to drop the 
immersion oil and adjust the iris ring (

Fig. 16

) to get proper 

brightness and contrast of view field.

 

 

Note

 

 

The condenser won

’t work well if no oil drop applied on the condenser.

 

 
 
 

8

 

Phase Contrast Kit Installation and Operation   
Instructions 

8.1  Phase contrast kits of A1PHB1 or A1PHB3: 

1)  Mounting the phase contrast objectives 

a. Take off all the objectives from the nosepiece. 
b. Install the phase contrast objectives onto the nosepiece following the steps in 2.3. 

2)  Mounting the phase contrast condenser/annular ring disk 

a. Rotate the nosepiece and set the 4x objective in position.

 

b. Turn the coarse focus knob to raise the mechanical stage to the highest position 

without contacting the 4X objective.

 

c.  Turn the condenser control knob to raise the condenser to the highest position.

 

d. Loosen the light collector and take it off.

 

e. Loosen the condenser lock thumb screw, pull down the condenser and take it off.

 

f.  Insert the condenser/annular ring disk into the condenser holder, and tighten the 

thumb screw.

 

g. Insert the light collector back onto the 

base and turn until it’s tightened.

 

h. Re-adjust the condenser height to its normal position.

 

i.  Re-adjust the mechanical stage height to its 

normal position.

 

Note:   

  When raising the mechanical stage, do not 

make contact with the objective. 

3)  Turn the desired objective into light path. 

4)  Turn the annular ring disk to put the corresponding 

ring into light path, i.e. if you are using the 40x 
phase contrast objective, you should turn the disk 
at 40 as shown in 

Fig. 17

 

Fig.16 

  Iris

 

Ring 

20 

Fig.17 

Summary of Contents for MD827S30 series























Reviews: