background image

11

Operation

CHECKING FOR LEAKS

WARNING

• 

Perform all leak tests outdoors.

•  Extinguish all open flames.

•  NEVER leak test when smoking.

• 

Do not use the heater until all connections have been leak tested and do not leak.

TO CHECK FOR A LEAK:

1.  Make 2-3 oz. leak check solution (one part liquid dishwashing detergent and three parts water).

2.  Apply several drops of solution where regulator connects to cylinder and to all hose and valve connections.

3. 

Make sure all patio heater and light valves are OFF.

4.  Turn cylinder valve ON.

If bubbles appear at any connection, there is a leak.

1. 

Turn cylinder valve OFF.

2. 

If leak is at regulator/cylinder valve connection:

 

Disconnect, reconnect, and perform another leak check. Apply the soapy solution to all hose and valve 

connections. If you continue to see bubbles after several attempts, cylinder valve is defective and should 

be returned to cylinder’s place of purchase.

3.  If leak is at hose/regulator connection:

 

This part is defective and you should contact the customer service department for replacement.

If NO bubbles appear at any connection, the connections are secure.

NOTE:

 Whenever gas connections are loosened or removed, you must perform a complete leak test.

CAUTION:

 Do not attempt to operate until you have read and understand all General Safety Information in this 

manual and all assembly is complete and leak checks have been performed.

BEFORE TURNING GAS SUPPLY ON

1. 

Your heater was designed and approved for outdoor use only. Do NOT use it inside a building, garage, or 

any other enclosed area.

2. 

Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or 

liquids.

3.  Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no 

leaks.

4. 

Be sure the cylinder cover is clear of debris. Be sure any component removed during assembly or servicing 

is replaced and fastened prior to starting.

BEFORE LIGHTING

1.  Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. 

Summary of Contents for PH-CN-0014





















Reviews: