background image

5

Safety and Warranty

installed, tested and serviced by qualified personnel only. Any adjustment whatsoever not expressly authorized 

and in disrespect of this manual voids the warranty. Observe all existing local regulations at the time of 

installation. Check that the characteristics of the electric grid correspond to the data given on the serial plate 

of the appliance. The packing materials (plastic bags, polystyrene, nails, etc.) as potential hazards, must be 

kept out of the reach of children and properly recycled according to the existing local regulations. For repairs 

contact Omcan and request the use of original spare parts. If in doubt do not use the appliance and contact 

Omcan. Not following the above conditions could risk the safety of those using the unit.

FOR YOUR SAFETY

Improper instillation, adjustment, alteration, service or maintenance can cause serious injury or property 

damage. Keep heater away from areas where flammable liquids, gasoline, vapors or explosives are stored 

or used. Gas leaks may cause a fire or explosion which can cause damage to property, serious bodily injury 

or death. Follow all leak-checking procedure before operating this unit highlighted in Step 8. If you smell gas: 

shut off gas to appliance, extinguish any open flame and if odor continues, contact your gas supplier or local 

fire department. This unit consumes air provide 1 inch² of opening for fresh air for each 1,000 Btu/Hr Input 

(2.22mm² / Wof Input). Never use open flame to check for leaks. Fuel systems must be installed by qualified 

and licensed personnel. Please contact your local gas supplier for these services.

•  Always maintain at least 18” clearance (top) and 24” clearance (side) from combustible materials. 

• 

Always place the heater on a hard a hard leveled surface. 

•  Do not use if the wind velocity is greater than 10 miles per hour.

•  Unit will operate at reduced efficiency below 40°F (5°C).

• 

It is normal for the heater to make hissing sounds at the start. This will decrease as the heater warms up.

• 

Keep sprinklers and other water sources away from burner and controls.

• 

Always use extreme caution when near the heater. Young children and pets should be supervised carefully 

when they are near the heater. Do not hand clothing or flammable materials on or near the heater. To avoid 

burns or clothing catching on fire, alert both children and adults to the hazards of high temperatures.

• 

Certain materials or items are susceptible to damage due to radiant heat when stored under heater.

• 

Do not alter heater in any manner.

• 

Inspect heater before each use. If a damaged part is detected, do not operate the heater until an original 

Omcan replacement part has been properly installed. Use of unauthorized parts will void warranty and 

create an unsafe condition.

• 

Prior to operating heater, replace any guards or protective devices removed from servicing.

• 

During operation, the surface of the heater of the burner assembly is very hot and should not be touched

•  After shutdown, do not touch burner assembly until heater has completely cooled down (approximately 45 

minutes after use.)

• 

The appliance and its individual shut off valve must be disconnected from the gas supply pipping system 

during any pressure testing. The system should be tested in the pressure in excess of 1/2 psig (3.5kpa).

• 

The appliance must be isolated from the gas supply piping system by closing its individual manual shut off 

valve during any pressure testing of the gas supply piping system at test pressure equal to or less than 1/2 

psig (3.5kpa).

•  Always perform a leak test on ga connections whenever heater is serviced. Never use a flame to test for 

leaks. Do not smoke while performing a test leak.

• 

Caution: It is essential to keep the heater’s valve compartment, burners and circulating air passage clean.

Summary of Contents for PH-CN-0014





















Reviews: