background image

AWS Installation and operating manual 

 

 

www.omega-air.si 

the  compressor  is  properly  set,  you  have  to  attach  it  to  the  ground  with  bolts or  screws 
(note to detach the compressor before moving it with the forklift)

. Each professional unit is 

in  accordance  with  all  the  valid  standards  and  subjected  to  intern  test  procedures.  But 
checking  the  equipment  before  transport  cannot  prevent  any  damage  that  might  appear 
during it. For this reason, the equipment is to be thoroughly checked before the start-up, to 
prevent  any  possible  damage.  Keep  the  compressor  under  observation  the  first  working 
hours to find any possible faults. 

INSTALLATION AND CONNECTION 

Preparing the place for installation and assembly 

 

Example of the basis: 

 

Picture 1: Dimensional drawing of the AWS basis 

At the basis, if there is a shaft a steel construction is advised (contact the manufacturer). The 
preparation of an appropriate basis is shown in the attachment. When setting up the foot of 
the equipment, spacers are mandatory for the connection of the foot and the basis. 
 

 

Electric installation: 

Supply cable with 3×2.5 mm

2

 wires, protected by 16 A type C circuit breakers. The length of 

the cable is a minimum of 0.5m. 

 

Condensate drain preparation: 

For the condensate drain, a 1/2˝galvanized pipe with an inner thread ending is required. The 
condensate drain connects to the drain on the central reservoir. 

 

Water supply preparation: 

Summary of Contents for AWS





















Reviews: