background image

5

ADDING OPTION CARDS

The DP63000 meters can be fitted with optional output cards and/or serial

communications cards. The details for the plug-in cards can be reviewed in the
specification section below. The plug-in cards, that are sold separately, can be
installed initially or at a later date.

WARNING: Disconnect all power to the unit before

installing Plug-in card.

Note

: Measurement errors may occur if signal input common is shared with

another circuit common (ie, serial common, Dual Sinking Output option card,
or Power Supply common) on multiple units.

SINGLE RELAY CARD

Type

: Single FORM-C relay

Isolation To Sensor & User Input Commons

: 1400 Vrms for 1 min.

Working Voltage: 150 Vrms

Contact Rating

: 1 amp @ 30 VDC resistive; 0.3 amp @ 125 VAC resistive

Life Expectancy

: 100,000 minimum operations

Response Time

:

Turn On Time: 4 msec max.
Turn Off Time: 4 msec max.

DUAL SINKING OUTPUT CARD

Type

: Non-isolated switched DC, N Channel open drain MOSFET

Current Rating

: 100 mA max. 

V

DS ON

: 0.7 V @ 100 mA

V

DS MAX

: 30 VDC

Offstate Leakage Current

: 0.5 mA max.

RS485 SERIAL COMMUNICATIONS CARD

Type

: RS485 multi-point balanced interface (non-isolated)

Baud Rate

: 300 to 38.4k

Data Format

: 7/8 bits; odd, even, or no parity

Bus Address

: 0 to 99; max 32 meters per line

Transmit Delay

: Selectable (refer to DP6-COM bulletin)

RS232 SERIAL COMMUNICATIONS CARD

Type

: RS232 half duplex (non-isolated)

Baud Rate

: 300 to 38.4k

Data Format

: 7/8 bits; odd, even, or no parity

O

PTIONAL

P

LUG

-

IN

C

ARDS

1.0 I

NSTALLING THE

M

ETER

INSTALLATION 

The meter meets NEMA 4X/IP65 requirements when properly installed. The

unit is intended to be mounted into an enclosed panel. Prepare the panel cutout
to the dimensions shown. Remove the panel latch from the unit. Slide the panel
gasket over the rear of the unit to the back of the bezel. The unit should be
installed fully assembled. Insert the unit into the panel cutout. 

While holding the unit in place, push the panel latch over the rear of the unit

so that the tabs of the panel latch engage in the slots on the case. The panel latch
should be engaged in the farthest forward slot possible. To achieve a proper seal,
tighten the latch screws evenly until the unit is snug in the panel (Torque to
approx. 28 to 36 in-oz [0.202 to 0.26 N-m]). Do not over-tighten the screws.

INSTALLATION ENVIRONMENT

The unit should be installed in a location that does not exceed the operating

temperature and provides good air circulation. Placing the unit near devices that
generate excessive heat should be avoided.

The bezel should only be cleaned with a soft cloth and neutral soap product.

Do NOT use solvents. Continuous exposure to direct sunlight may accelerate the
aging process of the bezel.

Do not use tools of any kind (screwdrivers, pens, pencils, etc.) to operate the

keypad of the unit.

2.0 S

ETTING THE

J

UMPERS

INPUT RANGE JUMPER

This jumper is used to select the proper input range. The input range selected

in programming must match the jumper setting. Select a range that is high
enough to accommodate the maximum signal input to avoid overloads. To
access the jumper, remove the rear cover of the meter. 

Warning

: Exposed line voltage exists on the circuit boards. Remove

all power to the meter and load circuits before accessing inside of
the meter.

REMOVING THE REAR COVER

To remove the rear cover, locate the cover locking tab below the 2nd and 3rd

input terminals. To release the tab, insert a small, flat blade screwdriver between
the tab and the plastic wall below the terminals. Inserting the screwdriver will
provide enough pressure to release the tab locks. To replace the cover, align the
cover with the input terminals and press down until the cover snaps into place.

Summary of Contents for DP63000A-I

















Reviews: