background image

20

2nd output group 

1012H 

Output value read and write of 

Output 1 

Unit is 0.1%, write operation is valid under manual tuning mode only. 

1013H 

Output value read and write of 

Output 2 

Unit is 0.1%, write operation is valid under manual tuning mode only. 

1016H 

Temperature regulation value 

-99.9 ~ +99.9. Unit is 0.1

1017H 

Analog decimal setting 

0 ~ 3 

101CH 

PID parameter selection 

0~5/AUTO 

101DH 

SV value corresponded to PID 

value 

Only valid within available range, unit: 0.1 scale 

1020H 

Alarm 1 type 

Please refer to the contents of the “Alarm Outputs” for detail 

1021H 

Alarm 2 type 

Please refer to the contents of the “Alarm Outputs” for detail 

1022H 

Alarm 3 type 

Please refer to the contents of the “Alarm Outputs” for detail 

1024H 

Upper-limit alarm 1 

Please refer to the contents of the “Alarm Outputs” for detail 

1025H 

Lower-limit alarm 1 

Please refer to the contents of the “Alarm Outputs” for detail 

1026H 

Upper-limit alarm 2 

Please refer to the contents of the “Alarm Outputs” for detail 

1027H 

Lower-limit alarm 2 

Please refer to the contents of the “Alarm Outputs” for detail 

1028H 

Upper-limit alarm 3 

Please refer to the contents of the “Alarm Outputs” for detail 

1029H 

Lower-limit alarm 3 

Please refer to the contents of the “Alarm Outputs” for detail 

102AH 

Read LED Status 

b0: ALM3, b1: ALM2, b2: 

, b3:

 ℉

, b4: ALM1, b5: OUT2, b6:OUT1, b7: AT 

102BH 

Read Pushbutton Status 

b1: F2, b2: Up, b3: Loop,    b5: F1, b6: Down, b7: Set, 0: press down key 

102CH 

Setting lock status 

102FH 

Software version 

V1.00 indicates 0x100 

1030H 

Start pattern number 

0 ~ 15 

1032H 

Remaining time of the executed 

step (second) 

Only read 

1033H 

Remaining time of the executed 

step (minute) 

Only read 

1034H 

No. of currently executed step 

Only read 

1035H 

No. of currently executed pattern  Only read 

1036H 

Read dynamic value in 

programmable control 

Only read 

1039H 

Communication write 

0: Disable (default), 1: Enable 

103AH 

Temperature unit display 

selection 

0:  , 1:   / 

linear input (default) 

103BH 

AT setting 

0: OFF (default), 1: ON 

103CH 

Control RUN/STOP setting 

0: STOP, 1: RUN (default), 2:END (program mode), 3: HOLD (program mode) 

101FH 

Start step number 

0 ~ 15 

1200H~13FFH 

Pattern 0~15 temperature set 

point setting (Even number) 
Pattern 0~15 execution time 

setting (Odd number) 

-999 ~ 9999
Time: 0 ~ 900

1 minute per scale

1400H~140FH  Actual number of step setting 

inside the corresponding pattern 

0 ~ 15 = N, indicate that this pattern is executed from step 0 to step N 

1410H~141FH 

Cycle  number  for  repeating  the 

execution  of  the  correspond 

pattern 

0 ~ 99 indicate that this pattern has been executed for 1 ~ 100 times 

1420H~142FH  Link pattern number setting of 

the correspond pattern 

0 ~ 15, 16 indicates the program end and keep in present step. 17 indicates the 

program end and execution end. 0~15 indicates the next execution pattern 

number after executing the current pattern 

Address 

Content 

Definition 

1100H 

Adjust Temperature Gain 

1101H 

Temperature Filter Range 

Range of temperature filter: 10~1000, unit: 0.01 

, default: 100(1.0

)

 

1102H 

Temperature Filter Factor 

Setting range: 0~50, default: 8 

1103H 

Reverse Output 

Bit1: output 2, Bit0: output 1 

1104H 

Slope of Temperature Increase 

Unit: 0.1 /

min or 0.1

/sec (refer to CommunicationAddress 1124H) 

1105H 

Remote Input Type Selection 

0: 0~20m A , 1: 4~20m A, 2: 0~5V, 3: 1~5V, 4: 0~10V 

Summary of Contents for CND3 Series





























Reviews: