background image

Feature #9                   Unlock #1 When Ignition Is Turned Off

       

(Factory Default Setting  On)

This feature configures the system to automatically unlock the vehicle’s

doors every time that the ignition switch is turned off.  An exception to this would
be if feature #11 is turned on, and a door being open when the ignition switch is
turned off.  If the system is installed without the Driver’s Door Priority unlock
interface, this feature unlocks all of the doors when the ignition switch is turned
off.  If Driver’s Door Priority is installed, this feature controls the driver’s door
only, and the next feature will control the automatic unlocking of the other doors.

Programming Unlock #1 When Ignition Is Turned Off:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released nine times.  The system’s response will be nine siren chirps, and the
Status Light flashing nine times, pausing, then repeating.  Within 10 seconds,
press and release the transmitter/transceiver’s "Arm/Lock" button to turn on
“Unlock #1 When Ignition Turned Off” (the siren will chirp once) or the "Disarm/
Unlock" button to turn this feature off (the siren will chirp twice).

Page 32

Feature #10

           Unlock #2 When Ignition Is Turned Off

 

      (Factory Default Setting  Off)

Explained in the previous feature, this feature controls the automatic unlock-

ing of all doors except the driver’s door if Driver’s Door Priority is installed.

Programming Unlock #2 When Ignition Is Turned Off:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released ten times.  The system’s response will be ten siren chirps, and the

Feature #8

         Doors Lock When Ignition Is Turned On

  

     (Factory Default Setting  On)

This feature configures the system to automatically lock the vehicle’s doors

every time that the ignition switch is turned on.  An exception to this would be
if feature #11 is turned on, and a door being open when the ignition switch is
turned on.  The two following features, #9 and #10, control the automatic
unlocking operation.

Programming Doors Lock When Ignition Is Turned On:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released eight times.  The system’s response will be eight siren chirps, and the
Status Light flashing eight times, pausing, then repeating.  Within 10 seconds,
press and release the transmitter/transceiver’s "Arm/Lock" button to turn on
“Doors Lock When Ignition Turned On” (the siren will chirp once) or the
"Disarm/Unlock" button to turn this feature off (the siren will chirp twice).

Sensors:

 

The Crime Guard 850i

4

 security system is equipped with a Glass

Breakage and Dual-Zone Infrasonic Impact Sensor to increase the effectiveness
of the system.  The impact sensor is just one in a comprehensive line of available
sensors. Other available options are: piezo shock sensors, and microwave/radar
sensors which can detect objects in motion both inside and outside the vehicle.
• The Crime Guard 850i

4

 control module features dual auxiliary sensor ports,

which easily allows the addition of a further optional sensor.

• If desired, the sensor zone only can be bypassed when the system is armed

with the transmitter or Echo transceiver, but leaving the other protection zones
in place.  This feature is convenient when environmental factors, such as hail
or thunder storms, may lead to the system being activated erroneously.

Prewarning Detection Circuit:

 

When the sensor’s prewarn zone is

violated the security system will respond by chirping the siren three times and
relocking all of the doors.* If the prewarn circuit is triggered five times while the
system is armed, the circuit will automatically shutdown until the security system
is disarmed and armed again.
• Prewarning operates from the Infrasonic Impact Sensor only.

GLASS BREAKAGE & 2-ZONE IMPACT SENSOR

* An optional doorlock interface must be installed

Page 17

THE DOORS WILL LOCK IF
ARMING, UNLOCK IF DISARMING

To Silently Arm or Disarm the System:

Press & Release the “Auxiliary #2 Output” Button ( II ) Twice

THE PARKING LIGHTS

WILL FLASH TWICE IF

ARMING, ONCE IF

DISARMING

Silent Arming and Silent Disarming are both operated by double-pressing the same transmitter button.

 Press

 2 X

 

Press

 

2 X

The transmitter or Echo transceiver can also silently Arm or Disarm the

system.  Pressing the “

II

” button twice simply reverses, or “toggles” the Armed

or Disarmed status that the system is in at the time.

THE SIREN
WILL NOT
CHIRP

SILENT ARMING AND DISARMING

Summary of Contents for Crime Guard 850i4



























Reviews: