Omega ORU52XL, Instruction Manual

6 

Installation Instructions 

Please ensure that all power is switched off before installing the range hood. 

Installation must be in accordance to the local electrical authority and codes. 

The switched power outlet for the range hood should be positioned to enable the user to turn the power off, 

to enable cleaning and any maintenance required. 

The switched power outlet should be installed within 600mm from the rear of the unit. 

Ensure that when installing the range hood, that it is protected from any possible damage from tools etc. 

Ducting for this unit must be installed in accordance to the local authority. 

Ensure that the fixings used for this range hood are suitable. 

Check the area where the range hood is to be fitted, to ensure that it is structurally sound. 

Before using the appliance, remove the plastic coatings protecting the stainless-steel finish. 

These models are intended to be installed into kitchen cabinetry. Take care that the cabinetry and 

supporting wall can carry the weight of the rangehood.  

Always double-check dimensions in this manual against the appliance before commencing.  
The rangehood should be placed at a minimum distance of 650mm from the cooking surface of the cooker 

below. Any more than 750mm could compromise the performance of the appliance. Drill a hole in the 

cupboard, 490*265mm for model ORU52XL and 665*265mm for model ORU70XL. Make sure the distance 

between the edge of the hole and the edge of the cupboard edge is at least 35mm. Remove the filter and 

remove the four screws holding the lower panel in place. Lift the appliance into the hole and check that it fits 

correctly (no gaps, does not interfere with anything above it etc.). Mark the hole positions with a pencil 

remove the appliance and pre-drill the holes using a small drill bit. Place the appliance back into position, 

line up the holes and fix into place using the 8 screws provided. Replace the cover & fix into position with 

the 4 screws and fit the filter. Fit the one-way filter to the top of the unit. 

The exhaust air vents through the one-way valve at the top. If the exhaust is to be vented away, cut a hole 

(~Ø160mm) in the top of the cupboard, and connect Ø150mm ducting to the one-way valve & pass it 

through the hole to wherever it is going. If the exhaust air is to be recirculated back into the room, either cut 

vents into the cupboard (with a minimum area of 800cm²), or leave the cupboard door open when in use. 

Once assembled in place, the appliance can be connected to the power supply. 

Operating Instructions 

Note

: Before the unit can be operated, it must either be ducted 

or, if the model is installed as a re-circulating range hood, it 

must be fitted with charcoal filters (one set supplied with the 

appliance). 
With the appliance fully installed and the power connected, the 

appliance can be used. 

• 

The light can be turned on & off by pressing the 

Light button. 

• 

The fan can be turned on and adjusted by pressing any of the three fan speed buttons (Low, Mid 

& High). 

• 

The fan can be turned off by pressing the Stop button.

7 

Replacing the LEDS 

Warning: Before attempting to replace the lights, ensure that the appliance is 

switched off and unplugged from the wall.  

• 

Remove the aluminium filter. 

• 

Press the lamp face and turn anti-clockwise to remove. 

• 

Replace with the same type of bulb (GU10 Base, 3W MAX). 

o

  Max Wattage: 2 x 3W 

o

  Voltage Range: 220 – 240V AC 

o

  ILCOS D Code: DR-3/65/1B-H-GU10-46/50 

• 

Replace the aluminium filter.  

Cleaning 

SAFETY PRECAUTION 

Before cleaning your rangehood or performing any maintenance, 

please ensure that the rangehood is turned off at the power point. 

Do not use abrasive cleaners to clean the rangehood. The use of 

warm soapy water and a cloth are recommended. 

Ensure that the rangehood is cleaned regularly, as a build-up of 

grease and fat may occur otherwise. 

The filters on the rangehood must be cleaned regularly to maintain efficiency, and prevent grease build up. 

The filter mesh is made of a high-density Stainless Steel. It is recommended that this is undertaken every 4 

– 6 weeks, depending on frequency of use. The filters can be cleaned with warm soapy water or a cloth. 

Cleaning of the rangehood must be performed as described above; otherwise there is a possibility of a fire 

hazard due to grease and fat build up. 

Troubleshooting 

Fault 

Possible Cause 

Solution 

Light on, but motor 

does not work 

Fan switch turned off 

Select a fan switch position. 

Fan switch failed 

Contact Everdure Service. 

Motor failed  

Contact Everdure Service. 

Light does not work, 

motor does not work 

House fuses blown 

Reset/Replace fuses. 

Power cord loose or disconnected 

Refit cord to power outlet. 

Switch power outlet on. 

Oil leakage 

One-way valve and the air ventilation 

entrance are not tightly sealed 

Take down the one-way valve and seal 

with sealant. 

Leakage from the connection of U-

shaped section and cover 

Take U-shaped section down and seal. 

Lights not working 

Broken/Faulty LED lamp 

Contact Everdure Service. 

Insufficient suction 

The distance between the rangehood 

and the gas top is too far  

Refit the rangehood to the correct 

distance. 

The Rangehood 

inclines 

The fixing screw not tight enough 

Tighten the hanging screw and make it 

horizontal.