710.1760.00.04-05
22/05/2014
41
В любом случае, перед тем, как начать выполнение работ на блоке, необходимо подождать, чтобы понизилась температура холодильной
установки, или уменьшить температуру окружающей среды.
При использовании таких устройств на производственных площадках, рекомендуется включать их в план предотвращения пожара и план
обеспечения безопасности завода. Чтобы избежать и предотвратить возможные риски возникновения пожара, удостоверьтесь в том, что
на производственных участках приняты все возможные меры предосторожности.
В случае утечек хладагента:
При вдыхании хладагента в больших количествах, это может вызвать удушье. Поэтому, существует необходимость обеспечения
производственных помещений, в которых установлена холодильная установка, адекватной вентиляцией.
Тщательно изучите таблицу данных по обеспечению безопасных условий труда с соответствующими значениями и предупреждениями.
Чрезмерное давление в линии заправки и нагнетания хладагента:
Данные контуры холодильной установки оснащаются предохранительными устройствами. Они должны устанавливаться техническим
персоналом, имеющим допуск на монтаж данных устройств. Установка предохранительных устройств должна соответствовать
национальным стандартам и выполняться в точном соответствии с ограничениями, изложенными в настоящем руководстве.
Угроза уменьшения озонового слоя:
Использование холодильного агента HFC, в соответствии с Постановлением CE/842/2006, уменьшает повреждение озонового слоя и
минимизирует парниковый эффект.
3.
ОПИСАНИЕ ХОЛОДИЛЬНОЙ УСТАНОВКИ, ЕЕ КОМПОНЕНТЫ И ОПЦИИ
3.1
ОПИСАНИЕ ХОЛОДИЛЬНОЙ УСТАНОВКИ
Холодильная установка поставляется полностью подготовленной к подсоединению. Она состоит из корпуса, полностью герметичного
контура охлаждения, контура холодильного агента и электрической цепи, в состав которой входят все управляющие и контролирующие
устройства, полностью работающие в автоматическом режиме. Выбранный и используемый охлаждающий агент должен отвечать
требованиям стандартов по защите окружающей среды и соответствующим правовым нормам.
3.2
СХЕМА ЦИРКУЛЯЦИИ ХОЛОДИЛЬНОГО АГЕНТА
СТАНДАРТНЫЕ КОМПОНЕНТЫ, ИСПОЛЬЗУЕМЫЕ В ХОЛОДИЛЬНОЙ УСТАНОВКЕ:
Вышеуказанные сокращения показывают позицию на чертежах.
Не все компоненты входят в состав всех моделей установки.
C– Компрессор
Компрессор улиточного типа герметичной конструкции с интегрированным биметаллическим выключателем и смотровым окном проверки
уровня масла.
Полу - герметичный компрессор:
Полу - герметичный компрессор с интегрированным биметаллическим выключателем и смотровым окном проверки уровня масла.
Возвратно - поступательный поршневой компрессор:
Возвратно - поступательный поршневой компрессор герметичной конструкции с интегрированным биметаллическим выключателем и, в
большинстве моделей, со смотровым окном проверки уровня масла.
CND – Конденсатор / Страховочные конденсаторные решетки.
Конденсатор наподобие теплообменника с оребрением состоит из медных трубок и алюминиевых ребер. Страховочные решетки корпуса
предохраняют конденсатор от механических повреждений. Месторасположение конденсатора позволяет избежать дополнительной
тепловой нагрузки на компоненты, расположенные внутри корпуса установки.
EVA – Испаритель
Испаритель представляет собой изолированный трубчатый теплообменник в кожухе или пластинчатый теплообменник из нержавеющей
стали.
HP – Прессостат высокого давления
Прессостат высокого давления предохраняет холодильный контур установки от чрезмерного рабочего давления (нарушение работы
установки при высоком давлении).
При данном виде неисправности, прессостат высокого давления отключает компрессор при превышении давления выше установленных
ограничений. Компрессор повторно не запустится до тех пор, пока дифференциальное давление не достигнет заданного значения, и не
будет нажата кнопка установки в исходное положение, установленная внутри холодильной установки.
Данная неисправность будет отображаться на блоке управления.
LP – Прессостат низкого давления
Прессостат низкого давления предохраняет холодильный контур установки от чрезмерно низкого рабочего давления (нарушение работы
установки при низком давлении). Когда происходит такой вид неисправности, прессостат низкого давления отключает компрессор в
случае выхода значения давления за установленные пределы. Компрессор повторно запустится в автоматическом режиме, когда
отношение давлений между контурами высокого и низкого давления, при помощи внутренней системы компенсации по давлению,
достигнет заданного значения. Данная неисправность будет отображаться на блоке управления в течение всего времени ее наличия.
Summary of Contents for CHG 08
