background image

 

Cod. 710.0167.01.00 Rev02 

– 10.2019 

© Copyright 2019 OMI Srl - All rights reserved

 

– 12

 

3.1 CONTROL PANEL 

The dryers are provided with an electronic control system. All adjustments and resets can be performed by means of the digital panel 
located on the front of the dryer. The control panel is composed of 5 keys (ON/OFF, TEST, SET, DOWN and UP) and a 3 digit display, 
with three signalling LEDs indicated by icons (PIC 1) 

 
 
 
 
 
 

PIC. 1  

 

 

 

DISPLAY VISUALIZATION

 

AND SIGNALLING LEDS (DD36 ÷ DD1000) 

 

 

DISPLAY VISUALIZATION

 

AND SIGNALLING LEDS (DD1300) 

 

 

 

 

DISPLAY 

DESCRIPTION 

 

the unit is in ENERGY SAVING mode 

 

the unit is ON with low load 

 

the unit is ON with normal load 

 

the unit is ON with normal-high load 

 

the unit is ON with high load 

LED 

STATUS 

DESCRIPTION

  

 

ON  

Compressor energized 

Blinking 

Programming mode activated 

 

ON 

Condensate drain energized

 

 

ON 

Speed of the fan = 100% 

Blinking 

Speed of the fan < 100% 

OFF 

Fan not running 

DISPLAY 

DESCRIPTION 

 

the unit is in ENERGY SAVING mode 

 

the unit is ON with low load 

 

the unit is ON with normal load 

 

the unit is ON with normal-high load 

 

the unit is ON with high load 

LED 

STATUS 

DESCRIPTION

  

 

ON  

Compressor energized 

Blinking 

Programming mode activated 

 

ON 

Condensate drain energized

 

 

Not used 

Not used 

Summary of Contents for DD36

















Reviews: