background image

 

 

DMAN-xxxx-xx

 

www.omnexcontrols.com

 

call toll free: 1-800-663-8806 

R170 Receiver 

The 

ORIGA

 

T150 / R170 

is a portable, long range, programmable radio remote control system.  Designed as a com-

pact and easy-to-use product, this member of the 

ORIGA

 family puts complete control of your machine where it’s 

needed most, with the operator.  It’s robust, easy to install and has complete self-diagnostics.  This system can be a 
simple cable replacement or add intelligence to make it a total control package. 

 
The 

ORIGA

 T150 / R170 system uses Frequency Hopping Spread Spectrum (FHSS) technology.  FHSS devices con-

centrate their full power into a very narrow signal that randomly hops from frequency to frequency within a designated 
band.  This transmission pattern, along with CRC-16 error-checking techniques, enables signals to overcome interfer-
ence that commonly affects licensed radios. 
 

The R170 receiver

 is designed to be powered from a 12VDC or 24VDC system.  The R170 is a radio receiver that 

takes commands from an OMNEX wireless transmitter and translates the commands into SAE J1939 or other CAN-
bus protocols.  The R170 has two CAN ports and can act as a CAN bridge.  A RS232 port allows the R170 to be con-
figurable, provide diagnostic information, firmware upgradeable and provides data logging capabilities. 

 

The T150 transmitter

 comes with 4 to 6 switches and an optional proportional trigger control.  It uses standard, long 

lasting AA batteries.  Each T150 transmitter uses a unique ID code to ensure that no two systems will conflict at a job 
site. 

Features 

 

• 

FCC, ISC, CE approved 

• 

License free 

• 

Weather proof 

• 

1200 foot range @ 900 MHz (900 ft @ 2.4 GHz) 

• 

Compact / weatherproof / ergonomic 

• 

Simple “wire-and-use” installation 

• 

Resilient to impact and shock 

• 

Available in both 900 MHz and 2.4 GHz 

• 

Available with E-Stop for ensured operator safety 

• 

Available with an optional pendant cable 

• 

Factory configurable for all custom applications. 

T150 Transmitter 

 System Overview

 

 

Battery Low LED 

Active LED 

E-Stop Button 

SW - 5 

SW - 6 

SW - 1 

SW - 2 

SW - 3 

SW - 4 

T150 Dimensions and Controls 

7.87” 

4.13” 

4.92” 

Summary of Contents for T150

















Reviews: