background image

 15 

 

7.1 STORAGE 

The unit can be used in a cold room, but it must be stored in a dry area at a temperature 
ranging from 0ºC/32ºF to 50ºC/122ºF . 

7.2 DECONTAMINATION REQUIREMENT 

Should an instrument or component that has been used with radioactive or pathogenic  
material require factory or field service, comply with the following procedure to ensure  
the safety of service personnel: 
 
Clean the parts to be serviced of all encrusted material and decontaminate them. There must 
be no radioactivity detectable by survey equipment. Obtain a Decontamination Certificate 
from Omni International. Complete the certificate and attach to the instrument or parts being 
returned. 
 
If no Decontamination Certificate is attached, and a potential radioactive or biological hazard 
is detected or suspected by Omni International, the equipment will not be serviced until prop-
er decontamination and certification is complete. The sender will be contacted for  
instructions as to the disposition of the equipment. Disposition costs will be borne by the 
sender. 

WARNING: 

It is a violation of federal law to transport biologically hazardous or radioactive 

materials without proper packaging, labeling, and appropriate warnings. 

SECTION 7. TRANSPORT, STORAGE & SERVICE 

PLEASE NOTE: 

The Sonic Ruptor 400 MUST be shipped in its original packaging. Failure to 

do so can result in serious damage to the unit and will void all warranties.  

Summary of Contents for Sonic Ruptor 400





















Reviews: