background image

10304055_EF.DOC

11/20

CLEANING AND MAINTENANCE

Disconnect from mains before starting maintenance operation!

DANGER TO LIFE!

We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use
alcohol or solvents!

There are no servicable parts inside the device except for the fuse. Maintenance and service operations are
only to be carried out by authorized dealers.

Replacing the fuse

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Please note:

 This fuse is being used for both 115 V and 230 V.

Before replacing the fuse, unplug mains lead.

Procedure:

Step 1:

 Open the fuseholder on the rearpanel with a fitting screwdriver.

Step 2:

 Remove the old fuse from the fuseholder.

Step 3:

 Install the new fuse in the fuseholder.

Step 4:

 Replace the fuseholder in the housing.

Should you need any spare parts, please use genuine parts.

If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply
cable available at your dealer.

Should you have further questions, please contact your dealer.

TECHNICAL SPECIFICATIONS

Power supply:

230 V AC, 50 Hz

Power consumption:

18 W

Slope:

24 dB / octave

Operation-modes:

2-way-stereo or 3-way-mono

Input:

Mono/stereo

Input impedance:

> 30,000 Ohms

Input jacks:

1/4" jack socket balanced and unbalanced

Output:

Mono/stereo

Output impedance:

500 Ohms

Output jacks:

1/4" jack socket balanced and unbalanced

Frequency range:

100 Hz - 10,000 Hz

Control range:

- ~ to + 6 dB

Dimensions:

483 x 44 x 160 mm

Weight:

2 kg

Fuse:

T 0,25 A, 250 V

Please note: Every information is subject to change without prior notice. 09.01.2003  ©

Summary of Contents for XO-2300












Reviews: