background image

12

CANADIAN DEPARTMENT OF COMMUNICATIONS NOTICE

NOTICE:  The Canadian Department of Communications Label identifies certified equipment.  This
certification means that the equipment meets certain telecommunications network protective, operational
and safety requirements.  The Department does not guarantee the equipment will operate to the user’s
satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company.  The equipment must also be installed using an
acceptable method of connection.  In some cases, the company’s inside wiring associated with a single
line individual service may be extended by means of a certified connector assembly (telephone
extension cord).  The customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier.  Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to disconnect the
equipment.

Users should ensure for their own protections that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together.  This
precaution may be particularly important in rural areas.
Caution:  Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage of total load to be
connected to a telephone loop which is used by the device, to prevent overloading.  The termination of a
loop may consist of any combination of devices subject only to the requirement that the total of the Load
Numbers of all the devices does not exceed 100.  The load number of this unit is 5.

This digital apparatus does not exceed the Class A limits for Radio noise emissions from digital
apparatus set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003
of the Department of Communications.

AVIS:  - L’étiquette du ministère des Communications du Canada identifie le materiel homologué.
Cette étiquette certifie que le matériel est conforme a certaines normes de protection, d’exploitation et
de sécurité des réseaux de télécommunications.  Le Ministère n’assure toutefois pas que le matériel
fonctionnera a la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations
de l’entreprise locale de télécommunication.  le matériel doit également etre installé en suivant une
méthod acceptée de raccordement.  Dans certains cas, les fils intérieurs de l’entreprise utilisés pour un
service indivuduel a linge unique peuvent etre prolongés au moyen d’un dispositif homologué de

Summary of Contents for Poll-Safe PS635

















Reviews: