background image

2

INPUT and OUTPUT PORT CONNECTIONS

The INPUT port of the PS635 is a male DB25 RS232 connector. The INPUT port connects to the PBX
or other source of call records.  The Input port is configured as DTE, similar to a PC serial port.

The PS635 Input port only requires connections to Ground and Receive Data to receive data from the
PBX.  Your PBX may require connection to some or all of the output pins of the PS635 Input port in
order to release data to the PS635.  When a device is properly connected to the PS635 Input port, the
PS635 RXD IN light will be lit green, and will flicker red when receiving data.

The Output port of the PS635 uses a female DB25 RS232 connector. The Output port connects to the
device used to process the call record data, usually a pc with call accounting software installed.  The
PS635 Output port is a DCE configuration similar to a modem or PBX.  When a device is properly
connected to the PS635 Output port the PS635 RXD AUX light will be lit green, and will flicker red
when releasing data.

RESET

PHONE LINE

DTE I

NPUT

(F

ROM

SMDR P

ORT

)

DCE O

UTPUT

(T

O

C

OMPUTER

)

12VAC

8

7

6

5

4

3

2

20

RECEIVE DATA:
REQUEST TO SEND:

DATA SET READY:

TRANSMIT DATA:

DATA TERMINAL READY:

CLEAR TO SEND

SIGNAL GROUND
DATA CARRIER DETECT:

(INPUT)

- Receives Call Data From Switch

(OUTPUT) - Pulled to RS232 High Level

(INPUT)

- Not Required

(OUTPUT) - XON/XOFF Handshaking Back to Switch

(OUTPUT) - DTR Handshaking to Switch

(INPUT)

- Receives Handshaking From Switch

(INPUT)

- Not Required

DTE Input port

8

7

6

5

4

3

2

20

TRANSMIT DATA:
REQUEST TO SEND:

DATA SET READY:

RECEIVE DATA:

DATA TERMINAL READY:

CLEAR TO SEND:

SIGNAL GROUND
DATA CARRIER DETECT:

(OUTPUT) - Transmits Call Data

(OUTPUT) - Pulled to RS232 High Level

(INPUT) - Commands and XON/XOFF Handshaking

(INPUT)

-

(OUTPUT) - Pulled to RS232 High Level

DCE

8

7

6

5

4

3

2

20

TRANSMIT DATA:
REQUEST TO SEND:

DATA SET READY:

RECEIVE DATA:

DATA TERMINAL READY:

CLEAR TO SEND:

SIGNAL GROUND
DATA CARRIER DETECT:

(OUTPUT) -
(INPUT) - Not Required

(OUTPUT) - Pulled to RS232 High Level

(INPUT) -

(INPUT)

- DTR Handshaking

(OUTPUT) - Pulled to RS232 High Level

(OUTPUT) - Pulled to RS232 High Level

DCE Output port

FIGURE 2. PS635 Input/Output Ports

Summary of Contents for Poll-Safe PS635

















Reviews: