background image

(1) Handle with care

     Do not drop G9SE to the ground or expose to excessive vibration or mechanical shocks. G9SE may be damaged
      and may not function properly.

(2) Adhesion of solvent such as alcohol, thinner, trichloroethane or gasoline on the product should be
      avoided. Such solvents make the marking on G9SE illegible and cause deterioration of parts.
(3) Conditions of storage
     Do not store in such conditions stated below.
       1) In direct sunlight
       2) At ambient temperatures out of the range of -10 to 55 

       3) At relative humidity out of the range of 25% to 85% or under such temperature change that causes  

condensation.

       4) At atmospheric pressure out of the range 86 to 106 kPa.
       5) In corrosive or combustible gases
       6) With vibration or mechanical shocks out of the rated values.
       7) Under splashing of water, oil, chemicals
       8) In the atmosphere containing dust, saline or metal powder and other conductive dusts.
         G9SE may be damaged and may not function properly.
(4) At least 50 mm above top face of G9SE and below bottom face of G9SE should be available to apply rated 
     current to outputs of G9SE and for enough ventilation.

(5) Mounting multiple units

 When mounting multiple units close to each other, the rated current will be 3 A. Do not apply a current

     higher than 3 A. If the output current is 3 A or more, make sure that there is a minimum distance of 
     10mm each between all adjacent G9SE units.

(6) DIN rail mounting
      Mount G9SE to DIN rails with attachments (TYPE PFP-M, not incorporated to this product), not to 
     drop out of rails by vibration etc. especially when the length of DIN railing is short compared to the widths of G9SE.

(7) Wire correctly according to   8    Wiring.

(8) Use cables with length less than 100 m to connect to Safety Inputs, Feed-back/Reset inputs, respectively. 
(9) G9SE may malfunction due to electro-magnetic disturbances.  Be sure to connect the negative terminal  of 
     DC power supply to ground. When using a DC power supply with light curtains, use DC power supply 
     which has no interruption by a power failure of 20 ms.
(10)This is a class A product. In residential areas it may cause radio interference, in which case the user may be
     required to take adequate measures to reduce interference.

(11) Do NOT mix AC load and DC load to be switched in the following terminals.

傍傍傍

- G9SE-201 : between 13-14 terminal and 23-24 terminal

傍傍傍

- G9SE-401 : between 13-14 terminal and 23-24 terminal, 33-34 terminal and 43-44 terminal

傍傍傍

- G9SE-221-T

Ƒ

 : between 13-14 terminal and 23-24 terminal, 37-38 terminal and 47-48 terminal

(12) Start entire system after more than 2s have passed since applying supply voltage to G9SE.

(13) Set the time duration of OFF-delay (Type 

G9SE-221-T

Ƒ

)

     1) Set the time duration of OFF-delay to an appropriate value 
         that does not cause the loss of safety function of system.
     2) 

Set both of the two Off-delay Time Preset Switches, one each 

         on the front and back, to the same value. When setting the 
         different value, it is detected as a fault.
         After setting, make sure G9SE operating time is correct.

(14) To determine safety distance to hazards, take into account the 

         

delay of Safety outputs caused by the following time:

      1) Response time
      2) Preset  off-delay time and accuracy of off-delay time
(15) Before G9SE outputs become in ON-state, non-regular self-
       diagnosis for Safety output circuit may be executed.
      On this occasion, the operating noise of internal relays occurs.
(16) In the place subjected to strong vibration or shock, mount G9SE
      to a mounting surface with screws and the screw mounting attachment. 
      Otherwise, G9SE may not function properly due to vibration or 
      mechanical shocks out of the rated values caused by sympathetic 
      vibration of G9SE and the mounting parts, and so on.

Appearance and Explanation of Each Parts

3

Ratings and Specifications

4

G9SE-201

G9SE-401

G9SE-221-T

Ƒ

Contact output
250 VAC  5 A       30 VDC  5 A (resistive load)

AC15: 240 VAC 2 A 
DC13: 24 VDC 1.5 A 

Switching specification for
Inductive load (IEC/EN60947-5-1)

Ratings

Specifications and performance

Operating time (OFF to ON state) (See Note2)

100 ms Max. (See Note3)

3 W max.

Type G9SE-221-T

Ƒ

4 W max.

4 W max.

300 m/s

2

Ambient humidity

Surrounding Air Temperature

Mechanical
shock resistance
(See Note7)

Vibration resistance (See Note6)

25

 to 85

RH

-10  to 55

 (No freezing or condensation)

Frequency:10 to 55 to 10 Hz   
Amplitude:0.35 mm half amplitude (0.7 mm double amplitude) 

15 ms Max.

1

Rated supply voltage

24 VDC

-15% to 10% of rated supply voltage

Suitability for Use

䣑䣯䣴䣱䣰䢢䣅䣱䣯䣲䣣䣰䣫䣧䣵䢢䣵䣪䣣䣮䣮䢢䣰䣱䣶䢢䣤䣧䢢䣴䣧䣵䣲䣱䣰䣵䣫䣤䣮䣧䢢䣨䣱䣴䢢䣥䣱䣰䣨䣱䣴䣯䣫䣶䣻䢢䣹䣫䣶䣪䢢䣣䣰䣻䢢䣵䣶䣣䣰䣦䣣䣴䣦䣵䢮䢢䣥䣱䣦䣧䣵䢢䣱䣴䢢䣴䣧䣩䣷䣮䣣䣶䣫䣱䣰䣵
䣹䣪䣫䣥䣪䢢䣣䣲䣲䣮䣻䢢䣶䣱䢢䣶䣪䣧䢢䣥䣱䣯䣤䣫䣰䣣䣶䣫䣱䣰䢢䣱䣨䢢䣶䣪䣧䢢䣒䣴䣱䣦䣷䣥䣶䢢䣫䣰䢢䣶䣪䣧䢢䣄䣷䣻䣧䣴䯑䢢䣵䢢䣣䣲䣲䣮䣫䣥䣣䣶䣫䣱䣰䢢䣱䣴䢢䣷䣵䣧䢢䣱䣨䢢䣶䣪䣧䢢䣒䣴䣱䣦䣷䣥䣶䢰䢢䣃䣶
䣄䣷䣻䣧䣴䯑䢢䣵䢢䣴䣧䣳䣷䣧䣵䣶䢮䢢䣑䣯䣴䣱䣰䢢䣹䣫䣮䣮䢢䣲䣴䣱䣸䣫䣦䣧䢢䣣䣲䣲䣮䣫䣥䣣䣤䣮䣧䢢䣶䣪䣫䣴䣦䢢䣲䣣䣴䣶䣻䢢䣥䣧䣴䣶䣫䣨䣫䣥䣣䣶䣫䣱䣰䢢䣦䣱䣥䣷䣯䣧䣰䣶䣵䢢䣫䣦䣧䣰䣶䣫䣨䣻䣫䣰䣩䢢䣴䣣䣶䣫䣰䣩䣵
䣣䣰䣦䢢䣮䣫䣯䣫䣶䣣䣶䣫䣱䣰䣵䢢䣱䣨䢢䣷䣵䣧䢢䣹䣪䣫䣥䣪䢢䣣䣲䣲䣮䣻䢢䣶䣱䢢䣶䣪䣧䢢䣒䣴䣱䣦䣷䣥䣶䢰䢢䣖䣪䣫䣵䢢䣫䣰䣨䣱䣴䣯䣣䣶䣫䣱䣰䢢䣤䣻䢢䣫䣶䣵䣧䣮䣨䢢䣫䣵䢢䣰䣱䣶䢢䣵䣷䣨䣨䣫䣥䣫䣧䣰䣶䢢䣨䣱䣴䢢䣣
䣥䣱䣯䣲䣮䣧䣶䣧䢢䣦䣧䣶䣧䣴䣯䣫䣰䣣䣶䣫䣱䣰䢢䣱䣨䢢䣶䣪䣧䢢䣵䣷䣫䣶䣣䣤䣫䣮䣫䣶䣻䢢䣱䣨䢢䣶䣪䣧䢢䣒䣴䣱䣦䣷䣥䣶䢢䣫䣰䢢䣥䣱䣯䣤䣫䣰䣣䣶䣫䣱䣰䢢䣹䣫䣶䣪䢢䣶䣪䣧䢢䣧䣰䣦䢢䣲䣴䣱䣦䣷䣥䣶䢮䢢䣯䣣䣥䣪䣫䣰䣧䢮
䣵䣻䣵䣶䣧䣯䢮䢢䣱䣴䢢䣱䣶䣪䣧䣴䢢䣣䣲䣲䣮䣫䣥䣣䣶䣫䣱䣰䢢䣱䣴䢢䣷䣵䣧䢰䢢䣄䣷䣻䣧䣴䢢䣵䣪䣣䣮䣮䢢䣤䣧䢢䣵䣱䣮䣧䣮䣻䢢䣴䣧䣵䣲䣱䣰䣵䣫䣤䣮䣧䢢䣨䣱䣴䢢䣦䣧䣶䣧䣴䣯䣫䣰䣫䣰䣩䢢䣣䣲䣲䣴䣱䣲䣴䣫䣣䣶䣧䣰䣧䣵䣵
䣱䣨䢢䣶䣪䣧䢢䣲䣣䣴䣶䣫䣥䣷䣮䣣䣴䢢䣒䣴䣱䣦䣷䣥䣶䢢䣹䣫䣶䣪䢢䣴䣧䣵䣲䣧䣥䣶䢢䣶䣱䢢䣄䣷䣻䣧䣴䯑䢢䣵䢢䣣䣲䣲䣮䣫䣥䣣䣶䣫䣱䣰䢮䢢䣲䣴䣱䣦䣷䣥䣶䢢䣱䣴䢢䣵䣻䣵䣶䣧䣯䢰䢢䣄䣷䣻䣧䣴䢢䣵䣪䣣䣮䣮䢢䣶䣣䣭䣧
䣣䣲䣲䣮䣫䣥䣣䣶䣫䣱䣰䢢䣴䣧䣵䣲䣱䣰䣵䣫䣤䣫䣮䣫䣶䣻䢢䣫䣰䢢䣣䣮䣮䢢䣥䣣䣵䣧䣵䢰
䣐䣇䣘䣇䣔䢢䣗䣕䣇䢢䣖䣊䣇䢢䣒䣔䣑䣆䣗䣅䣖䢢䣈䣑䣔䢢䣃䣐䢢䣃䣒䣒䣎䣋䣅䣃䣖䣋䣑䣐䢢䣋䣐䣘䣑䣎䣘䣋䣐䣉䢢䣕䣇䣔䣋䣑䣗䣕䢢䣔䣋䣕䣍䢢䣖䣑䢢䣎䣋䣈䣇䢢䣑䣔
䣒䣔䣑䣒䣇䣔䣖䣛䢢䣑䣔䢢䣋䣐䢢䣎䣃䣔䣉䣇䢢䣓䣗䣃䣐䣖䣋䣖䣋䣇䣕䢢䣙䣋䣖䣊䣑䣗䣖䢢䣇䣐䣕䣗䣔䣋䣐䣉䢢䣖䣊䣃䣖䢢䣖䣊䣇䢢䣕䣛䣕䣖䣇䣏䢢䣃䣕䢢䣃䢢䣙䣊䣑䣎䣇
䣊䣃䣕䢢䣄䣇䣇䣐䢢䣆䣇䣕䣋䣉䣐䣇䣆䢢䣖䣑䢢䣃䣆䣆䣔䣇䣕䣕䢢䣖䣊䣇䢢䣔䣋䣕䣍䣕䢮䢢䣃䣐䣆䢢䣖䣊䣃䣖䢢䣖䣊䣇䢢䣑䣏䣔䣑䣐䢢䣒䣔䣑䣆䣗䣅䣖䢪䣕䢫䢢䣋䣕
䣒䣔䣑䣒䣇䣔䣎䣛䢢䣔䣃䣖䣇䣆䢢䣃䣐䣆䢢䣋䣐䣕䣖䣃䣎䣎䣇䣆䢢䣈䣑䣔䢢䣖䣊䣇䢢䣋䣐䣖䣇䣐䣆䣇䣆䢢䣗䣕䣇䢢䣙䣋䣖䣊䣋䣐䢢䣖䣊䣇䢢䣑䣘䣇䣔䣃䣎䣎
䣇䣓䣗䣋䣒䣏䣇䣐䣖䢢䣑䣔䢢䣕䣛䣕䣖䣇䣏䢰

PNP transistor output    Load current

100 mA DC max.

G9SE-201

G9SE-401

G9SE-221-T

Ƒ

Contact resistance (See Note4)

100 mΩ Max.

Maximum cable length

100 m Max.

Reset input time

250 ms Min. 

Accuracy of OFF-delay time

Within plus or minus 10

 of

the set value 

Impulse
withstand
voltage
(IEC/EN
60947-5-1)

Insulation resistance

100 MΩ Min.

5,000,000 operations Min. 

Mechanical durability

50,000 operations Min.

Minimum applicable load

Pollution degree

2

Over voltage category (IEC/EN60664-1)

Safety output: Class 

䱸䢮䢢䣶䣪䣧䢢䣱䣶䣪䣧䣴䣵䢼䢢

Class 

䱷䢢

Degree of protection

IP20

Weight

approx. 150 g

approx.180 g

approx.180 g

Note:
(1) Power consumption of loads not included .

(2) This does not include the bounce time of internal relay in the G9SE.
(3) This  is in normal operation. When executing 

non-regular self-diagnosis for Safety output circuit,

    G9SE operating time become 500 ms max..
(4) This is initial value using the voltage-drop method with 1A at 5VDC.   
(5) Use for each contact output an 8A fuse that conforms to IEC 60127 as a short-circuit protection device. 
    This fuse is not included with the G9SE.
(6) Condition: G9SE is mounted to  

mounting surface with screw and the screw mounting attachment.

    In the case of DIN rail mounting, mount DIN rail with G9SE to the place without big vibration. 
    (Amplitude guideline: Less than 0.15 mm half amplitude (0.3 mm double amplitude))

Conditional short-circuit current
(IEC/EN60947-5-1)

100 A (See Note5)

Preset Switches

 

(only applies to Type G9SE-221-T

Ƒ

)

Change the value of the preset switches only when G9SE is disconnected from power supply.

Function

Presets OFF-delay

time (duplicate)

(*1)

Name

OFF-delayed

time preset

switch

Value
For Type G9SE-221-T05

0(default setting value)/0.1/0.2/0.3/0.4/0.5/0.6/0.7/0.8/1.0/1.5/2.0/2.5/3.0/4.0/5.0(s)(*2) 

For Type G9SE-221-T30 

0(default setting value)/1/2/4/5/6/7/8/9/10/12/14/16/20/25/30(s)(*2)

(*1)Set both of the two Off-delay Time Preset Switches, one each on the front and back, to the same value.
    When setting the different value, it is detected as a fault.
(*2)See following illustration for setting position of Off-delay Time Preset Switch. Make sure that the direction of cutting 
      edge of preset switch is correctly pointed to the off-delay time value which must be set.

ex.1) 0 second off-delay setting

ex.2) 1.5 second off-delay setting

OFF-DELAY

0

5.0

4.0

3.0

2.0

1.5

1.0

0.8

0.7

0.6

0.5

0.4

0.3

0.1

0.2

2.5

OFF-DELAY

0

5.0

4.0

3.0

2.0

1.5

1.0

0.8

0.7

0.6

0.5

0.4

0.3

0.1

0.2

2.5

cutting edge

LED Indicators

Marking Color

Name

Function

PWR

Green

Power supply
Indicator

Lights up while power is supplied.
Blinks corresponding to the occurring error

IN1

Orange

Safety Input 
#1 indicator

Lights up while high signal is input to T12
Blinks when error relating to Safety  input #1 occurs. 

IN2

OUT

OUT1

Lights up while Safety outputs (13-14, 23-24, 33-34, 43-44) are in ON-state.
Blinks when an error relating to Safety output occurs.

OUT2

Lights up while off-delayed Safety outputs (37-38, 47-48) are in ON-state.
Blinks when an error relating to Safety off-delayed solid-state output occurs.

Input current

ON voltage

Type G9SE-401

Type G9SE-221-T

Ƒ

Type G9SE-201

Reset/Feedback
Input

Safety Outputs
(Instantaneous)

Safety Outputs (OFF-delay)

OFF-delay
time preset
switch

Power Supply

Safety Input1

Safety Input2

Auxiliary output

Precautions for Correct Use

6 kV

24 VDC 4 mA

Inputs

OFF voltage

OFF current

11 VDC Min.

5 mA Min.

5 VDC Max.

1 mA Max.

Electrical durability

Contact
outputs 

Insulation
specification

Dielectric
strength

1,500 VAC

Destruction

Malfunction

100 m/s

 22.5 

 124 

 109 

 4 

 111.6 

 4 

 3 

 6.6 

 3 

 17.5 

Type G9SE-201 Type G9SE-401

Type G9SE-221-T

Ƒ

5.6 

5.6 

R2.3 

 11.4 

 9.9 

 71 

 73.5 

Mounting holes

 133 ±0.3

Two, 4.2 dia.
or M4

䣕䣥䣴䣧䣹䢢䣯䣱䣷䣰䣶䣫䣰䣩
䣣䣶䣶䣣䣥䣪䣯䣧䣰䣶

Insert

(1) Use G9SE within an enclosure with IP54 protection or higher of IEC/EN60529.
(2) When ready for wiring, the power source shall be disconnected first. Further, at operating this unit, do not touch 
      the terminals in order to prevent an electrical shock.
(3) Do not apply any excessive voltage or current to the input or output circuit the G9SE. Doing so may result in damage 
      to the G9SE or cause a fire.
(4) Incorrect wiring may lead to loss of safety function. Wire conductors correctly and verify the operation of G9SE
      before commissioning the system in which G9SE is incorporated. 
(5) Do not apply DC voltages exceeding the rated voltages, or AC voltages to G9SE.
(6) Use SELV/PELV DC porwer supply satisfying requirements below to prevent electric shock.
      - DC power supply with double or reinforced insulation, for example, according to IEC/EN60950 or EN50178 or 

a transformer according to IEC/EN61558.

      - DC supply satisfies the requirement for class 2 circuits stated in UL 508.
(7) The lifetime of G9SE depends on the conditions of switching of its outputs. Be sure to conduct its test operation 
      under actual operating conditions in advance and use it within appropriate  switching cycles. Apply protection 
      circuitry against back electromotive force in case connecting inductive loads to safety outputs.
(8) Do not operate the G9SE with flammable or explosive gas. An arc with operation and the heat of relay will cause
      a fire or an explosion.
(9) Do not 

drop G9SE to the ground or 

dismantle, repair, modify G9SE, 

otherwise an electric shock may occur or 

      the G9SE may malfunction

.  It may lead to loss of its safety functions.

(10) Use protective device (Fuse etc.) for short-circuit protection and ground fault protection, otherwise a fire may occur 
        or the G9SE may malfunction.
(11) Auxiliary monitoring outputs are NOT safety outputs. Do not use auxiliary outputs as any safety output.

 Such incorrect use causes loss of safety function of G9SE and its relevant system.

(12) After installation of G9SE, qualified personnel shall confirm the installation, and shall conduct test
        operations and maintenance.
        The qualified personnel shall be qualified and authorized to secure the safety on each phases of design,
        installation, running, maintenance and disposal of system.
(13) A person in charge, who is familiar to the machine in which G9SE is to be installed, shall conduct and verify 
        the installation.

Type G9SE-201
Type G9SE-221-T

Ƒ

Type G9SE-401

4022078-4 C

Original instructions

Safety Relay Unit

USER'S MANUAL

English

Thank you for purchasing G9SE Safety Relay Unit.
Please read and understand this manual before using the products.
Keep this manual ready to use whenever needed. 
Only qualified person  trained in professional electrical technique should handle G9SE.
Please consult your OMRON representative if you have any questions or comments.

EU/EC Declaration of Conformity

OMRON declares that G9SE series are in conformity with the requirements of the following 
EU/EC Directives. If you need a complete Declaration of Conformity, please contact your 
Omron representative:
 - EMC Directive: 2004/108/EC, 2014/30/EU
 - Machinery Directive: 2006/42/EC

G9SE series are designed and manufactured in accordance with the following standards:
 - EN ISO13849-1: 2008  PL e  Category 4 
 - IEC/EN 60947-5-1, 

- IEC/EN 62061 SIL3,

 - EN81-1  

 

- EN81-2

 - UL508   

 

- CAN/CSA C22.2 No.14 

- GB14048.5

Standards

Precaution for Safe Use

WARNING

Indicates a potentially hazardous situation which, if not avoided, will 
result in minor or moderate injury, or may
result in serious injury or death. 
Additionally there may be significant property damage.

Meanings of Signal Words
The following signal words are used in this manual.

Indicates prohibited actions

Meaning of Alert Symbols
The following alert symbols are used in this manual.

Indicates mandatory actions

Alert Statements

Serious injury may possibly occur due to breakdown of safety outputs.
Do not connect loads beyond the rated value to the safety outputs.

Serious injury may possibly occur due to loss of required safety functions.
Wire G9SE properly so that supply voltages or voltages for loads do NOT touch the 
safety inputs accidentally or unintentionally.

WARNING

Serious injury may possibly occur due to loss of safety functions.
Use appropriate devices referring to the information shown below.

Controlling Devices
Emergency stop switch

Door interlocking switch 
Limit switch
Safety Sensor

Relay with forcibly guided 
contacts

Contactor

Other devices

Requirements
Use approved devices with Direct Opening Mechanism complying with 
IEC/EN 60947-5-1
Use approved devices with Direct Opening Mechanism complying with 
IEC/EN 60947-5-1 and capable of switching micro loads of 24VDC, 5mA.
Use approved devices complying with the relevant product standards, 
regulations and rules in the country where it is used.
Use approved devices with forcibly guided contacts complying with 
EN 50205.
For feedback purpose use devices with contacts capable of switching 
micro loads of  24VDC, 5mA.
Use contactors with forcibly guided mechanism to input the signal to 
Feedback/Reset input of G9SE through the NC contact of the contactor.
For feedback purpose use devices with contacts capable of switching 
micro loads of 24VDC, 5mA.
Failure to open contacts of a contactor cannot be detected by monitoring 
its auxiliary NC contact without forcibly guided mechanism.
Evaluate whether devices used are appropriate to satisfy the requirements 
of safety category level.

Precautions for Safe Use

(14) Perform daily and 6-month inspections for the G9SE. Otherwise, the system may fail to work properly, 
        resulting in serious injury. Turn OFF the signal to Safety input and make sure G9SE operates without fault by 
        checking the state of the LED indicator in inspection.
(15) Conformity to requirements of performance level is determined as an entire system. It is recommended to consult 
        a certification body regarding assessment of conformity to the required safety level.
(16) OMRON shall not be responsible for conformity with any safety standards regarding to customer's entire 
        system.

(17) Dispose of the Units according to local ordinances as they apply.

Internal Connection

2

余傍

Type G9SE-201

余傍

Type G9SE-

01

余傍

Type G9SE-221-T

Ƒ

$

$

7 7

7 7

 

6DIHW\

2XWSXWV

LQVWDQWD

QHRXV

 

   

7 7

5HVHW

)HHGEDFN

,QSXW

6DIHW\

,QSXW

3RZHU

VXSSO\

FLUFXLW

6DIHW\

,QSXW

7

;

$X[LOLDU\

2XWSXW

6DIHW\

2XWSXWV

2))

GHOD\

$

$

7 7

7 7

 

6DIHW\

2XWSXWV

LQVWDQWD

QHRXV

 

   

7 7

5HVHW

)HHGEDFN

,QSXW

6DIHW\

,QSXW

3RZHU

VXSSO\

FLUFXLW

6DIHW\

,QSXW

7

;

$X[LOLDU\

2XWSXW

$

$

7 7

7 7

 

6DIHW\

2XWSXWV

LQVWDQWD

QHRXV

 

7 7

5HVHW

)HHGEDFN

,QSXW

6DIHW\

,QSXW

3RZHU

VXSSO\

FLUFXLW

6DIHW\

,QSXW

7

;

$X[LOLDU\

2XWSXW

Dimensions

Orange

Orange

Orange

Safety Input 
#2 indicator
Safety Output 
indicator

OFF-delayed
Safety Output 
indicator

Lights up while high signal is input to T22
Blinks when error relating to Safety  input #2 occurs. 

cutting edge

Power
input

Outputs

Item

Operating voltage range

Rated power consumption (See Note1)

Safety output
OFF-delayed Safety output

Auxiliary output

Response time (ON to OFF state) 

Note: Specifications  subject  to  change  without  notice.

OMRON  Corporation (Manufacturer)

Shiokoji Horikawa, Shimogyo-ku, Kyoto, 600-8530 JAPAN

Regional Headquarters
OMRON EUROPE B.V. 
(Representative and Importer in EU)

Wegalaan 67-69, 2132 JD Hoofddorp
The Netherlands

 Contact:  www.ia.omron.com

OMRON ASIA PACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 
(Lobby 2), Alexandra Technopark, 
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower, 
200 Yin Cheng Zhong Road, 
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200

OMRON SCIENTIFIC TECHNOLOGIES INC.

6550 Dumbarton Circle Fremont 
CA 94555 U.S.A
Tel: (1) 510-608-3400/Fax: (1) 510-744-1442

[mm]

Type G9SE-221-T

Ƒ

Type G9SE-221-T

Ƒ

Between input
and output
Between
different poles
of output
Between input
and output
Between
different poles
of output

2,200 VDC

6 kV (between 13-14/23-24 and 33-34/43-44(37-38/47-48))

4 kV (between 13-14 and 23-24, 

between 33-34(37-38)

 and 

43-44(47-48)

)

Continued on back page

Reviews: