Omron H7BR Series Manual Download

Page: 1 / 22

Digital Counter

H7BR

Easy-to-Use Multifunction Counters
with Backlit LCD Display

■

Compact, 72 mm (2.83 in) square
— includes single and double preset,
and +/– range

■

Both contact and transistor outputs
available

■

Prescale function displays in units
of actual physical parameters
(length, volume, etc.)

■

H7BR-C provides large/small
discrimination mode — ideal for
positioning and production control

■

Batch counter in H7BR-B lets you
count in dozens, hundreds, or any
count preset

■

On-line change of set value possible

Ordering Information

When placing your order, add the supply voltage to the part number from those listed below. For example, H7BR-BV 100 to 240 VAC.

Number of presets

One

Two (Non-independent)

Input type

No voltage

Voltage

No voltage

Voltage

Contact and sink (NPN)

H7BR-B

H7BR-BV

H7BR-BW

H7BR-BWV

transistor outputs

Contact and source (PNP)

H7BR-BP

H7BR-BVP

H7BR-BWP

H7BR-BWVP

transistor outputs

Supply voltages

100 to 240 VAC, 50/60 Hz or 24 VAC/12 to 24 VDC

■

STANDARD COUNTERS

Number of presets

One

Two (Non-independent)

Input type

No voltage

Voltage

No voltage

Voltage

Contact and sink (NPN)

H7BR-C

H7BR-CV

H7BR-CW

H7BR-CWV

transistor outputs

Contact and source (PNP)

H7BR-CP

H7BR-CVP

H7BR-CWP

H7BR-CWVP

transistor outputs

Supply voltages

100 to 240 VAC, 50/60 Hz or 24 VAC/12 to 24 VDC

■

REVE/– RANGE COUNTERS

■

ACCESSORIES

Description

Part number

Soft cover with two mounting clips for front panel protection

Y92A-72F1

Shock prevention terminal cover protects wiring connections

Y92A-72T

NEMA 4 water proof cover

Y92A-72N

Summary of Contents for H7BR Series























Search results

Summary of Contents for H7BR Series

Reviews:

Related manuals for H7BR Series

Brands by name

Popular brands

Omron H7BR Series, Manual

Search results

Summary of Contents for H7BR Series

Reviews:

Related manuals for H7BR Series

Brands by name

Popular brands