background image

H7CZ

7

Accessories (Order Separately)

Protecting the Counter in Environments Subject to Oil

The Waterproof Packing will deteriorate, harden, and shrink 
depending on the application environment. To ensure maintaining the 
IP

@

6, UL Type 4X waterproof level, periodically replace the 

Waterproof Packing. The periodic replacement period will depend on 
the application environment. You must confirm the proper 
replacement period. Use 1 year or less as a guideline. If the 
Waterproof Packing is not replaced periodically, the waterproof level 
will not be maintained. It is not necessary to mount the Waterproof 
Packing if waterproof construction is not required.

Note: Depending on the operating environment, the condition 

of resin products may deteriorate, and may shrink or 
become harder. Therefore, it is recommended that resin 
products are replaced regularly.

The H7CZ's panel surface is water-resistive (conforming to IP

@

6, 

UL Type 4X) and so even if drops of water penetrate the gaps 
between the keys, there will be no adverse effect on internal circuits. 
If, however, there is a possibility of oil being present on the 
operator's hands, use the Soft Cover. The Soft Cover ensures 
protection equivalent to IP54F against oil. Do not, however, use the 
H7CZ in locations where it would come in direct contact with oil.

Soft Cover

Y92A-48F1

Hard Cover

Y92A-48

Flush Mounting Adapter

Y92F-30

Order this Flush Mounting Adapter separately 
if it is required.

Waterproof Packing

Y92S-29

Order this Waterproof Packing 
separately if it is required.
The Waterproof Packing can be used 
to achieve IP66 protection.

Summary of Contents for H7CX-R11D1





















Reviews: