19
Troubleshooting
Problem
Cause
Remedial Action
■
The power
cannot be
turned on.
■
The batteries are inserted in
wrong direction.
⇒
Insert the batteries in correct direction.
(Refer to page 7)
■
The power
turns off
too soon.
■
The power
turns off
while using
the unit.
■
The Pads are not attached to
the skin.
■
Pads are removed from the skin.
■
The batteries are worn out.
■
The power turns off automatically
in 15 minutes.
■
The Electrode Cord is broken.
⇒
If the Pads are not attached to the skin, the power
will turn off automatically.
(Refer to page 7)
⇒
If the Pads come off from the skin, the power
will turn off automatically.
(Refer to page 7)
⇒
Replace the batteries with new ones.
(Refer to page 7)
⇒
Turn off the Intensity Dial/Power Button.
Unless it is turned off, the batteries will wear out
slightly faster.
(Refer to page 12)
⇒
Replace the Electrode Cord.
(Refer to page 20)
■
The Pad
does not
attach to the
skin.
■
The clear film on the adhesive
surface of the Pad is not peeled off.
■
The adhesive surface of Pad is dirty.
■
You used the Pad immediately
after washing it.
■
The adhesive surface of Pad is
damaged.
⇒
Peel off the clear film on the adhesive surface.
(Refer to page 7)
⇒
Wash the adhesive surface softly with your fingertips
under slow running water for several seconds.
(Refer to page 17)
⇒
Sufficiently dry it and leave the adhesive surface to
airdry.
(Refer to page 17)
⇒
Pad is a consumable.
Replace the Pad with a new one.
(Refer to page 20)
■
The
adhesive
surface of
Pad is sticky.
■
You used the Pad while you
were perspiring.
■
You washed the Pad too long
and too frequently.
■
You stored the Pad under high
temperature, high humidity, and
direct sunshine.
⇒
Leave the Pad in the refrigerator overnight.
(Refer to page 17)
■
Cannot
feel the
stimulation.
■
The Pad is not attached close to
the skin.
■
The Pads are attached
overlapping each other.
■
The Electrode Cord is not
connected correctly.
■
The intensity is adjusted too weak.
■
The batteries are worn out.
■
The adhesive surface of Pad
is damaged.
⇒
Attach the Pad close to the skin.
(Refer to page 7)
⇒
Attach the Pads by not overlapping them.
(Refer to page 7)
⇒
Connect the Electrode Cord correctly.
(Refer to page 7)
⇒
Turn the Intensity Dial/Power Button.
(Refer to page 12)
⇒
Replace the batteries with new ones.
(Refer to page 7)
⇒
Pad is a consumable.
Replace the Pad with a new one.
(Refer to page 20)
■
The skin
turns red.
■
The skin
feels
irritating.
❇
If the unit does not operate after taking the above-mentioned measures, contact the nearest OMRON dealer.
■
The treatment time is too long.
■
The Pad is not attached close to
the skin.
■
The adhesive surface of Pad is
dirty or dried.
■
The adhesive surface of Pad is
damaged.
⇒
Limit the treatment time to 10 to 15 minutes.
(Refer to page 12)
⇒
Attach the Pad close to the skin.
(Refer to page 7)
⇒
Wash the adhesive surface of Pad softly with your
fingertips for several seconds under slow
running water.
(Refer to page 17)
⇒
Pad is a consumable.
Replace the Pad with a new one.
TENS-EN01-22[HV-F127]-2 11/17/03 6:49 PM Page 20
