background image

7

Safety precautions

Caution

 (for battery replacement)

If you notice abnormal sound or smell, smoke, or leakage from the inside,
immediately turn off the power switch and disconnect the AC input plug
from a wall outlet (commercial power).

Using the unit under such conditions may cause a fire.

If you notice such a condition, stop using the unit and contact us at _____ for inspection and repairs.

Use the unit under the conditions in which you can immediately disconnect the AC input plug
from a wall outlet (commercial power) in the case of an abnormal event.

If fluid leaks from the unit, do not touch the fluid.

Doing so may cause blindness or burns.

If the fluid contacts your eyes or skin, wash it out with lots of clean water and consult your doctor.

Caution

 (for maintenance)

Perform replacement on a stable and flat place.

Handle the battery carefully not to drop it.

Not doing so could cause injury or burns due to liquid (acid) leakage.

Use a specified battery for replacement.

Not doing so may cause a fire.

Product model: BXB50F (battery pack for BX35F/BX50F/BX50FW)

BXB75S (battery pack for BX75SW)

Do not replace the battery in a place where there is flammable gas.

Spark may occur when connecting the battery, which may cause an explosion or fire.

If fluid (dilute sulfuric acid) leaks from the battery, do not touch the fluid.

Doing so may cause blindness or burns.

If it contacts your eyes or skin, wash it out with lots of clean water and consult your doctor.

Do not disassemble or modify the battery.

Doing so could cause dilute sulfuric acid leak, which could cause blindness and burns.

Do not drop the battery or do not give strong impact on it.

Dilute sulfuric acid may leak.

When maintaining the connected equipment, turn OFF the power switch
and disconnect the AC input plug.

Even if you disconnect the AC input plug while the UPS is operating, the power output of this
unit does not stop and power is supplied from the outlet during a power failure.

Do not disassemble, repair, or modify the unit.

Doing so may cause an electric shock or a fire.

If fluid leaks from the unit, do not touch the fluid.

Doing so may cause blindness or burns.

If the fluid contacts your eyes or skin, wash it out with lots of clean water and consult your doctor.

Do not throw the unit into fire.

The lead battery in the unit may explode, or leak dilute sulfuric acid.

Caution

 (for use)

Summary of Contents for POWLI BX35F




























































Reviews: