SIEPCYEUOQ2V01A Q2V Technical Manual
127
Table 4.13 Auto-Tuning Input Data in EZ Open Loop Vector Control Method
Input Data
Parameter
Unit
Auto-Tuning Mode
(T4-01 Setting)
Motor Constant
(0)
Static R Autotune
(1)
Motor Type Selection
T4-02
-
x
-
Motor Max Revolutions
T4-03
min
-1
x
-
Motor Rated Revolutions
T4-04
min
-1
x
-
Motor Rated Frequency
T4-05
Hz
x
-
Motor Rated Voltage
T4-06
V
x
-
PM Motor Rated Current (FLA)
T4-07
A
x
x
PM Motor Rated Power (kW)
T4-08
kW
x
-
Number of Motor Poles
T4-09
-
x
-
◆
ASR and Inertia Tuning
To increase drive responsiveness and prevent hunting, use Auto-Tuning to automatically adjust the control-related
parameters. These types of Auto-Tuning are available for the control system:
•
Deceleration Rate Tuning
•
KEB Tuning
Note:
If you do Control Tuning, you cannot set
H1-xx = 61 [Motor 2 Select]
. Do not do Control Tuning for applications that switch between
motor 1 and motor 2.
Table 4.14 Control Loop Tuning Selection
Mode
Parameter
Settings
Application Conditions and Benefits
Applicable Control Methods (A1-02 Settings)
V/f Control
(0)
OLVector
(2)
PM
OLVector
(5)
PM
AOLVector
(6)
EZ Vector
(8)
Deceleration Rate
Tuning
T3-00 = 2
To automatically adjust the deceleration rate to
prevent an
ov [Overvoltage]
fault.
x
x
x
x
x
KEB Tuning
T3-00 = 3
•
To automatically adjust parameter settings to
prevent an
ov [Overvoltage]
fault with the KEB
Ride-Thru function.
•
When
L3-11 = 1 [Overvolt Supression Select =
Enabled]
.
x
x
x
x
x
■
Deceleration Rate Tuning
Deceleration Rate Tuning automatically sets the deceleration rate to prevent an
ov [Overvoltage]
fault during
motor deceleration. Set
C1-11 [Accel/Decel Time Switchover Freq]
first to automatically set parameters
C1-02
[Decel Time 1]
(high speed range) and
C1-08 [Decel Time 4]
(low speed range).
■
KEB Tuning
KEB Tuning automatically sets parameters used for the KEB Ride-Thru function and for the overvoltage
suppression function.
Control Tuning automatically sets these parameters in to the best values.
Table 4.15 Parameters set in Control Tuning
Parameters Automatically Set
Deceleration Rate Tuning
KEB Tuning
C1-02 [Decel Time 1]
x
-
C1-08 [Decel Time 4]
x
-
C1-09 [Fast Stop Time]
-
x
L2-06 [KEB Decel Time]
-
x
L3-25 [Load Inertia Ratio]
-
x
*1
The drive automatically sets
C1-08 [Decel Time 4]
only when
C1-11 [Ac/Dec Switch Frequency] ≠ 0
.
*2
When
L2-29 = 1 [KEB Method = Single KEB1 Ride-Thru]
, the drive will automatically adjust
C1-09 [Fast Stop Time]
and will not
adjust
L2-06 [KEB Decel Time]
. If you must not change the Fast Stop time, do not do KEB Tuning.
Summary of Contents for Q2V Series
