No.
Name
Description
Range
Def.
Control
Mode
Addr. Hex Pg.
V/f OL
V PM
E3-04
Motor 2 Max Output
Frequency
These parameters set the V/f pattern for motor 2.
To set linear V/f characteristics, set the same values for
E3-07 and E3-09. In this case, the setting for E3-08 will be
disregarded. Ensure that the four frequencies are set
according to these rules or oPE10 fault will occur:
E3-04 ≥ E3-06 > E3-07 > E3-09
E3-09 E3-07 E3-06 E3-11 E3-04
E3-05
E3-12
E3-13
E3-08
E3-10
VACrms Out (V)
Frequency (Hz)
40.0 to
400.0
50 Hz
A
A
−
31A
149
E3-05
<24>
Motor 2 Max
Voltage
0.0 to 255.0 200.0 V A
A
−
31B
149
E3-06
Motor 2 Base
Frequency
0.0 to
E3-04
50 Hz
A
A
−
31C
149
E3-07
Motor 2 Mid Output
Freq.
0.0 to
E3-04
2.5 Hz
<53>
A
A
−
31D
149
E3-08
<24>
Motor 2 Mid Output
Freq. Voltage
0.0 to 255.0
16.0 V
<12>
<53>
A
A
−
31E
149
E3-09
Motor 2 Min.
Output Freq.
0.0 to
E3-04
1.3 Hz
<53>
A
A
−
31F
149
E3-10
<24>
Motor 2 Min.
Output Freq.
Voltage
0.0 to 255.0
12.0 V
<12>
<53>
A
A
−
320
149
E3-11
<26>
Motor 2 Mid Output
Frequency 2
0.0 to
E3-04
0.0 Hz
A
A
−
345
149
E3-12
<24>
<52>
Motor 2 Mid Output
Frequency Voltage
2
0.0 to 255.0
<24>
0.0 Vac
A
A
−
346
149
E3-13
<24>
Motor 2 Base
Voltage
0.0 to 255.0
<24>
0.0 Vac
A
S
−
347
149
E4: Motor 2 Parameters
Use E4 parameters to control a second motor operating on the same drive.
E4-01
Motor 2 Rated
Current
Sets the motor 2 nameplate full load current in amperes (A).
This value is automatically set during Auto-Tuning.
10 to 200%
of drive
rated
current
<57>
A
A
−
321
150
E4-02
Motor 2 Rated Slip
Sets the motor 2 rated slip in Hz. Automatically set during
Auto-Tuning.
0.00 to
20.00
<57>
A
A
−
322
150
E4-03
Motor 2 Rated No-
Load Current
Sets the magnetizing current of motor 2 in Ampere.
Automatically set during Rotational Auto-Tuning.
0 to less
than E4-01
<27>
<57>
A
A
−
323
150
E4-04
Motor 2 Motor
Poles
Sets the number of poles of motor 2. This value is
automatically set during Auto-Tuning.
2 to 48
4 poles
A
A
−
324
150
E4-05
Motor 2 Line-to-
Line Resistance
Sets the phase-to-phase resistance of motor 2 in ohms.
Automatically during Auto-Tuning.
0.000 to
65.000
<37>
<57>
A
A
−
325
151
E4-06
Motor 2 Leakage
Inductance
Sets the voltage drop due to motor leakage inductance as a
percentage of rated voltage of motor 2. Automatically set
during Auto-Tuning.
0.0 to 40.0
<57>
A
A
−
326
151
E4-07
Motor 2 Motor Iron-
Core Saturation
Coefficient 1
Set to the motor iron saturation coefficient at 50% of
magnetic flux. Automatically set during Rotational
Auto-Tuning.
0.00 to 0.50
0.50
−
A
−
343
151
E4-08
Motor 2 Motor Iron-
Core Saturation
Coefficient 2
Set to the motor iron saturation coefficient at 75% of
magnetic flux. This value is automatically set during
Rotational Auto-Tuning.
Setting for
E4-07 to
0.75
0.75
−
A
−
344
151
E4-09
Motor 2 Mechanical
Loss
Sets the motor mechanical loss as a percentage of motor
rated power (kW) capacity.
Adjust in the following circumstances:
• When there is a large amount of torque loss due to motor
bearing friction.
• When there is a large amount of torque loss.
0.00 to 10.0
0.0
−
A
−
33F
151
E4-10
Motor 2 Iron Loss
Sets the motor iron loss in watts.
0 to 65535
<57>
Α
−
−
340
151
E4-11
Motor 2 Rated
Capacity
Sets the motor rated capacity in kW. Automatically set
during Auto-Tuning.
0.00 to
650.00
<12>
A
A
−
327
151
E4-12
Motor 2 Iron-Core
Saturation
Coefficient 3
Set to the motor iron saturation coefficient at 130% of
magnetic flux. Automatically set during Rotational
Auto-Tuning.
1.30 to 5.00
1.30
−
A
−
342
151
E4-14
<22>
Motor 2 Slip
Compensation Gain
Sets the slip compensation gain for motor 2. The function
is the same as C3-01 for motor 1.
Refer to C3-01: Slip
Compensation Gain on page 127
.
0.0 to 2.5
0.0
<53>
A
A
−
341
152
E4-15
Torque
Compensation Gain
- Motor 2
Sets the torque compensation gain for motor 2. The function
is the same as C4-01 for motor 1.
Refer to C4-01: Torque
Compensation Gain on page 128
.
1.00 to 2.50
1.00
A
A
−
341
152
B.2 Parameter Table
310
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
7/16/2008-13:23
