Omron WLM - Datasheet Download

Page: 1 / 10

Long-life Two-circuit Limit Switch

WLM

F-99

Lim

Switch

Long-life Two-circuit Limit Switch

WLM

New Long-life Limit Switches Added to the
Wide Variety of WL Models

• Improved resistance to abrasion and smoother movement in the

head section means that a mechanical life of 30,000,000 oper-
ations minimum is now a reality.

• Wiring and replacement for maintenance purposes are easy

done.

• Fluorescent indicators improve visibility when setting stroke

zones.

Model Number Structure

■

Model Number Legend

1. Actuators

CA2:

Roller lever: Standard

GCA2:

Roller lever: High-precision

H2:

Roller lever: Overtravel, general-purpose

G2:

Roller lever: Overtravel, high-sensitivity

2. Wiring Specifications

Blank:

Screw terminal: G1/2 conduit

K13A:

Direct-wired connector: 2-core, AC

K13:

Direct-wired connector: 2-core, DC

K43A:

Direct-wired connector: 4-core, AC

K43:

Direct-wired connector: 4-core, DC

-M1J:

Pre-wired connector: 2-core, DC (See note.)

-AGJ03:

Pre-wired connector: 4-core, AC (See note.)

-DGJ03:

Pre-wired connector: 4-core, DC (See note.)

Note:

With 0.3-m cable attached.

WLM

-LD

Summary of Contents for WLM -











Search results

Summary of Contents for WLM -

Reviews:

Related manuals for WLM -

Brands by name

Popular brands

Omron WLM -, Datasheet

Search results

Summary of Contents for WLM -

Reviews:

Related manuals for WLM -

Brands by name

Popular brands