background image

In the case that brand number 0000 was selected the whole database of 

either TV or Aux is scanned. The device-LED shows a reverse blink for each 

transmission.

•  Note that the search sequence continues by going through the whole list

  after scanning through the brand list when all code-sets for the brand are

  tested. It only stops when all code-sets of the whole database are tested.

•  When the TV/AUX turns off or mute, the user must release the POWER or

  MUTE key. The user should switch the TV/AUX on again with the original or

  the universal remote control it device turn off. Now all keys can be tried

  out with the universal remote control (inverse blinking if a universal

  function-code is available under the key) including the POWER and MUTE

  key. Press <<POWER>> or <<MUTE>> for 5 secs to continue the code-set

  selection (item iv, above).

•  If the 4 digit code is wrong or if another key than the <<POWER>> or

  <<MUTE>> key is pressed after the 4 digits, Auto brand search will be

  exited and the unit will not change the universal code-set number for the

 respective 

device.

•  Exiting a successful setup is via pressing the TV mode key twice or after

 timeout.

9

Summary of Contents for iLifeTV













Reviews: