WWW.ONEFORALL.COM
13
If you should wish to remotely control lamps and lighting as well as Energy
Saving, you can also use the Energy Saver remote to control the separately
available One For All Light Accessories.
Lighting Control
- Voltage and Load: 230V~
- Degree of Protection: IP 20
- Radio Frequency: 433.92MHz
- RF Range: Typically 30m in open area.
- Max power for HC-8000: 1000 Watt
Specification HC-8000
It is possible to change the number you use to select the HC8000 Power Plug. This is useful
if you have purchased a second Power Plug (available from One For All), or if you already
have a Power Plug operating as number 1.
To assign a number to the plug, follow these steps:
•
Plug your device (or extension lead) the HC-8000 into the wall If you are
setting up a device with an in-line switch (such as a lamp), make sure the
switch is set to On
•
Press the Energy Saver key on your ONE FOR ALL URC-8350 so that it is
in Energy Saving Mode.
•
Press the number you wish to assign to the Power Plug Switch
(HC-8000). If this is your first Plug, number 1 is recommended, number 2
for the second etc. The IR Indicator (LED) at the top of the URC-8350
should blink twice.
•
Press and hold the button on the Power Plug (HC-8000) until the red
light begins to blink.
•
Press the Channel Up (+) key. The red light on the Light Power Plug
(HC-8000) should stop flashing.
The remote should now operate the Power Plug (HC-8000).
To test it, check if the Channel Up (+) and (-) keys work to switch your light ON
and OFF respectively,.
•
If you require more than 10 plugs to control, you can also use the Red, Green, Yellow
and Blue keys on your remote to control 11-14. Simply assign these keys to the Power
Plugs HC-8000) as you would do a number.
•
If you experience interference, it is possible to change the code of the Energy Saver
Mode on your remote to avoid this. The default code is 41000, but it is possible to
change the code to 41001, 41002 etc up to 41015. To change the code, set the Light
Mode up as you would do a normal device (see page 5), using codes 41000 - 41015.
•
If you should wish to reset your Power Plug HC-8000 to factory defaults so you can
assign it a new number, hold down the button on the Light Control Switch until the
red light starts to blink, release the button and then hold it down again until the red
light goes out.
How to change the number of your HC-8000
1
2
3
URC_8350_V_2_19feb08.qxd:Ofa5_Digital_URC7555_EURO_10_Talen 20-02-2008 16:24 Pagina 13
Summary of Contents for URC-8350
