background image

16 

 

5 .   B A T T E R I E S   A N D   C H A R G I N G  

Use these specifications to reorder deep-cycle batteries

 

Type

           

  Deep-cycle (sealed lead-acid or gel cell) 

Voltage

       

  12-volts each 

Amperage

     

50 AH   

Approx Size:   

200mm x 170mm x 170mm 

 

To change a battery 

1.

 

Remove seat and rear shroud. Please see Figure 8. 

Disassembly and Assembly.

 

2.

 

Remove the battery tie-down strap. 

3.

 

Disconnect the battery cables from the electronic controller module. 

4.

 

Disconnect the battery cables from the battery terminals. 

5.

 

Remove the old battery. 

6.

 

Place a new battery in the battery well. 

7.

 

Connect the red battery cable to the positive (

) battery terminal. 

8.

 

Connect the black battery cable to the negative (

) battery terminal. 

9.

 

Reconnect the battery cables to the electronic controller module. 

10.

 

Fasten the battery tie-down strap. 

11.

 

Replace rear shroud and seat. 

 

Why do my new batteries seem weak? 

Deep-cycle batteries employ a different chemical technology than is used in car batteries, nickel-cadmium 

batteries (NiCad), or in other common battery types. Deep-cycle batteries are specifically designed to 

provide power, drain down their charge, and then accept a relatively quick recharge. 

We work closely with battery manufacturers to provide batteries best suited to the s

cooter’s specific 

electrical demands. During shipping, the batteries may encounter temperature extremes that may 

influence their initial performance. Heat diminishes the charge on the battery; cold slows the available 

power and extends the time needed to recharge the battery. 

It may take a few days for the temperature of your s

cooter’s batteries to stabilize and adjust to their new 

room or ambient temperature. 

More importantly, it takes a few charging cycles (a partial drain followed by a full recharge) to establish 

the critical chemical balance that is essential to a deep-

cycle battery’s peak performance and long life.

 

 

 

 

5 .   B A T T E R I E S   A N D   C H A R G I N G  

 

The following steps will maximise the batteries` life and efficiency: 

 

1.

 

Fully recharge any new battery prior to its initial use. This charging cycle brings the battery to about 

Summary of Contents for B9200



























Reviews: