background image

23 

 

If the connections are good, charge the battery.

 

High Battery Fault. 

The battery voltage is too high. This may occur if 

overcharged and/or travelling down a long slope.

 

If travelling down a slope, reduce your speed to minimise the 

amount of regenerative charging. Check the battery charger. 

Current Limit or Controller Overheated. 

The motor has been 

exceeding its maximum current rating. The scooter may have stalled. 

Turn the scooter off, leave for a few minutes and turn back on again. 

The motor may be faulty. Check the motor and associated 

connections and wiring.

 

Park Brake Fault. 

Either the park brake release switch is active or

 

the 

park brake is faulty.

 

Check the park brake and associated

 

connections 

and wiring.

 

Ensure the free-wheel lever is engaged. 

Drive Inhibit. 

Either a Charger

 

Inhibit or OONAPU condition has 

occurred.

 

Disconnect the Battery Charger.

 

Ensure the throttle is in 

neutral when turning

 

on the controller.

 

The throttle may require 

re-calibration.

 

Speed Control Fault. 

The throttle, speed limit pot, or the

 

associated 

wiring may be faulty. Check the throttle, speed pot, associated 

connections and wiring.

 

Motor Fault. 

The motor or its associated wiring is faulty.

 

Check the 

motor and associated

 

connections and wiring.

 

Other Error. 

The controller may have an internal fault.

 

Check all 

connections and wiring.

 

 

If the problems persist after you have these checks described above please contact your service agent. 

 

 

9 .   C A R E   A N D   M A I N T E N A N C E  

 

Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your 

ability to perform the maintenance listed below, you may schedule inspection and maintenance at your 

authorised dealer. 

 

The following areas require periodic inspection and/or care and maintenance. 

TYRE PRESSURE 

           

For optimum scooter performance we recommend that the tyre pressure be maintained at 30-35 psi. 

TIRE CONDITION AND TREAD WEAR 

Regularly inspect your s

cooter’s tires for signs of wear.

 

           

Use a rubber conditioner on your s

cooter’s ty

res to help to preserve them. 

Summary of Contents for B9200



























Reviews: