background image

information.  If unreadable or missing, contact Harbor Freight Tools for a
replacement.

3.

Do not force the equipment.  This Sprayer will do the work better and safer at
the speed and capacity for which it was designed.

SKU 92497           For technical questions, please call 1-800-444-3353           PAGE 5

4.

         WARNING!   Risk of injection or severe injury.  Keep clear of Nozzle
(2, 6).  Do not direct discharge stream at people or animals. 
 Keep the work
area clear of all people and animals.

5.

Never use hot liquids over 130  Fahrenheit.  Dry running will cause serious
damage to the seals.  
Make sure the water or liquid chemical supply used for
the Sprayer is not dirty, sandy, and does not contain any corrosive chemical prod-
ucts.

6.

To avoid electrical shock, never start or run the Sprayer in the rain.  Never
allow water or liquid chemicals to leak inside the Pump & Battery Housing (26) of
the Sprayer.  Do not direct discharge stream at the Pump & Battery Housing
itself, its Power Plug (29), or at other live electrical equipment.

7.

When using the Sprayer, always maintain a firm grip on the Spray Gun (1)
with both hands.
  Squeezing the Handle (11) of the Spray Gun causes a kick-
back force.

8.

Do not pull or carry the Sprayer by its Hose (16) or Wire (13), or pull the
Hose/Wire around sharp corners or edges.  
Do not unplug the Spray Gun (1)
by pulling on the Hose/Wire.  Keep the Hose/Wire away from heated surfaces.

9.

Avoid unintentional starting.  Make sure you are prepared to begin work
before turning on the Sprayer.

10.

The work area should have adequate drainage to reduce the possibility of a
fall due to slippery surfaces.

11.

This product is intended for outdoor residential household use only.

12.

Keep the Hose (16) connected to the Pump & Battery Housing (26)  and
Spray Gun (1) while the system is pressurized.  
Disconnecting the Hose while
the unit is pressurized is potentially dangerous, and may cause injury.

13.

Prior to starting the Sprayer in cold weather, check all of the parts of the
unit to make sure ice has not formed.  
Do not store the unit where the tem-
perature will fall below 32  Fahrenheit.
(See “Inspection, Maintenance, and Cleaning” section.)

o

o

Summary of Contents for 92497













Reviews: