5
18
Dust Deputy® Owner’s Manual © 2010
Dust Deputy® Owner’s Manual © 2010
XI. Super Dust Deputy®
Turn Any Single Stage Collector Into A Super Cyclonic Dust Collector!
1. Add A Super Dust Deputy® Cyclone.
Dust Collector, Dust Drum, Flex Hose
and Filter not included.
23”
Turn your inefficient single stage or two stage collector into a
high efficiency cyclonic collector using your existing blower.
Retrofits to single stage 1/2hp to 3hp dust collectors.
High efficiency cyclone separates 98% of wood waste before
the filter. Filter clogging no longer reduces air flow.
Compact footprint. Simple installation.
Reduced filter maintenance and no dusty bags to empty.
Benefits & Features:
System
Dimensions
Height approx. 23”
Inlet Diameter: 5” O.D.
Outlet Diameter: 6”
Powder Coated Paint
Finish Over Steel
Super Dust Deputy® - AXD002030
2. Turn cyclone upside-down and
place it on the floor or other flat
surface. Turn drum lid over and
align bolt holes in lid with bolt holes
in cyclone base. Put bolt through
washer, then put bolt and washer
through lid from the underside of lid
and attach with whiz nut. Tighten nut
and repeat with all six bolts. Thor-
oughly tighten hardware to eliminate
air leaks.
2.
3. Put cyclone and lid on
top of optional dust drum
then attach and seal with
clamp ring.
3.
1. Apply gasket around the inlet hole
in the drum lid, making sure that the
gasket goes inside the bolt holes and
around the inlet hole. An air tight seal
is extremely important for good dust
collection. Make sure ends of gasket
butt together and there are no gaps.
1.
Add one of our HEPA
media filter retrofit kits to
your collector for even
better filtration. See the
accessories page.
SDD000002 - Drum Dolly Frame - 10 gal. (1)
SEX100000 - Drum Lid (1)
RHC000006 - Caster (4)
VXC110002 - Plastic Cyclone (1)
SES100000 - 10 gal. Steel Drum w/ Clamp (1)
AXD250066 - Hose 2.5”x 5.5’ (1)
VFA050015 - Grounding Tape (1)
BBS001205 - Plastic Spacer (1)
AXG000004 - Gasket (1)
AFW380125 - Felt Washer (1)
AFW180000 - Washer Flat 5/16” (1)
AFW025000 - Washer Flat 1/4” (6)
AFT155175 - Whiz Nut 5/16” (4)
AFT000005 - Whiz Nut 1/4” (7)
AFS015920 - Hex Bolt 1/4-20 x 3/4” (6)
AFB025175 - Carriage Bolt 1/4-20 x 1 3/4” (1)
VXC160001 - 16” Cyclone (1)
DAS050000 - Adapter Spiral 5” (1)
AFS015920 - Bolts 1/4-20 x 3/4 (6)
AFT000005 - Whiz Nut 1/4 (6)
AFW025000 - Washer 1/4 (6)
RGZ125250 - Gasket 1/8 x 1/4 (2ft.)
Optional:
SEK170601 - 17 gal. Steel Drum Kit
For additional
static reduction,
install metal
grounding tape
as shown.
Place supplied gasket on drum
top, lining up holes in gasket
with holes in lid. Put metal tape
on cyclone as shown then place
bolt through washer then put bolt
through hole in base of cyclone.
Secure with nut underneath.
Gasket
Drum Lid
Cyclone
Bolt
1/4”-20 x 3/4”
Washer 1/4”
Whiz Nut 1/4”
IV. 10 Gal. Deluxe Contents
10 Gal Deluxe Dust Deputy® -
AXD000010
10 Gallon Drum Dolly Assembly - SDD000002
Super Dust Deputy Assembly
U.S. Patent #7,282,074 C1
U.S. Design Pat.
App. # 29/358,526
29/358,497
29/342,738
1. Install the (4) casters by inserting stems throught the four perimeter holes in
dolly legs. Put on a 5/16” lock nut on each caster stem and tighten with a wrench.
2. Measure, center punch and drill a 1/4” hole in the center of drum bottom.
3. First put metal washer, then felt washer on the 1/4”- 20 carriage bolt. Insert
bolt into the drilled hole from
INSIDE
the drum. Slip nylon spacer over bolt so
that it is on the outside of drum against the bottom. Put caster plate over the bolt
and tighten with 1/4”- 20 lock nut as shown in photo. This allows the felt washer
to seal the hole in the drum. It is very important for your unit’s performance that
there are no air leaks.
Caster
Caster
Plate
Drum
Felt
Washer
5/16”
Washer
1/4”- 20
Bolt
Nylon
Spacer
5/16”
Lock
Nut
1/4”
Lock
Nut
Note: Dust
drum may be
white or black.
