background image

• 

• 

• 

• 

DO NOT stand on the desk. Do not use the desk as a stepladder.

ed.

Every 6 months, check all bolts and screws to ensure they are tight.

This product is California 93120 Compliant for Formaldehyde.

16 of 16

PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION

Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This warranty is made by

 

Comfort Products only to the original end-user customer acquiring the product directly from Comfort Products’ authorized dealers

as shown by the original sales receipt. The end-user customer remedy pursuant to this warranty is limited to repair or replacement of

 

parts at Comfort Products’ option within a reasonable amount of time. Comfort Products reserves the right to require damaged parts 

to be returned to Comfort Products upon request. Consent from Comfort Products must be obtained before any warranty work is

 

performed. This warranty applies under conditions of normal use and is not subject to defects caused by improper assembly or 

disassembly; defects occurring after purchase due to product mo

 

sure

 

to the elements; labor or assembly cost. This warranty does not cover the cost of transportation or labor. In no event shall Comfort 

Products be liable in either tort or  contract for any loss or direct, special, incidental, consequential or exemplary damages. This Limited

 

Warranty is NOT applicable to end-user customers who use Comfort Products for rental purposes. This warranty applies only to end-user

 

customers in the United States. All warranties are limited to t

165 pounds for the desktop, 11 pounds for the drawers, 22 pounds for the middle shelf, 44 pounds for the bottom shelf, and 22 pounds

 

for the hutch. For claims or questions concerning this warranty, please visit: www.comfortproducts.net or email us at: 

customerservice@comfortproducts.net

MODEL: # 50-LD01

L

O

Comfort Products, Inc. 
122 Gayoso Avenue, Suite 101 
Memphis, TN 38103

www.comfortproducts.net
email: customerservice@comfortproducts.net

Summary of Contents for 50-LD01LO

















Reviews: