OPERATION
This list is almost endless. Provided the product is non porous and can
normally be immersed in water almost anything can be thoroughly
cleaned. Here are some examples:
●
Turbochargers
●
Motorcycle radiators
●
Vehicle differentials
●
Sugical equipment
●
Engine cylinder heads
●
Bicycle derailleurs
●
Coins and other collectibles
●
Milking parlour equipment
●
Golf clubs&grips&golf balls
●
Printer heads and toner cartridges
●
Horse bits&stirrups &horse brasses
●
Motorcycle engine crank cases
●
Knives, bayonets and other militaria
●
Gun and gun components
●
Jewellery especially gold,
silver & platinum
●
Watchstraps
●
Tattoo needles
●
PCB Boards etc
●
Engine/Model parts
●
Toothbrushes & Dentures
●
Electrical components
●
Make-up cases
●
Diesel injection pumps
Ultrasonic cleaning is not recommended for the following gemstones:
Opal, Pearl, Emerald, Tanzanite, Malachite, Turquoise, Lapis and Coral.
4
Keep it away from children !
This device is not intended to use by individuals with restricted physical sensory or metal
capacities or those with lack of experience or knowledge, include children, unless they are
supervised by an individual who is responsible for their safety or have received training in oper-
ating the device .
Please read the following very carefully as failure to comply may invalidate your
guarantee
1) DO NOT run the cleaner continuously for more than one hour at a time, as doing so can
damage the internal components.
2) DO NOT operate the unit without fluid in the tank. Always ensure the fluid is no higher than
the max mark, Always ensure there is a minimum depth of 7cm.
3) DO NOT drop any item into the tank as this may cause damage to the transducer. Always
place the items gently into the tank and use the basket whenever possible.
4) The more items that you place in your cleaning bath the less efficient it will clean. It is not
advised to overlap items. Always allow plenty of clear space between the items.
5) Do keep the lid on during use. This will prevent splashes and reduce evaporation of the fluid.
6) Never immerse the machine or power cord in water or other liquid.
7) DO NOT touch the power plug with wet hands, especially when inserting or removing the plug.
Remove the power plug from the socket first.
9) DO NOT disassemble the machine, except by professionals.
10) UNPLUG the power source while filling or emptying the tank.
11) DO NOT spray water or liquid over the device and the control panel
12) DO NOT operate the cleaner without proper grounding.
13) DO NOT place the device on a soft surface, where the vents could be blocked.
14) Always turn the heater off after using as leaving it on can cause the fluid to evaporate and
damage the internal components.
15) Upon completion of the cleaning cycle, turn the heater button off and isolate the machine
from the electrical supply.
16) Take care when adding or removing items from the cleaning tank as the fluid is likely to be
hot and displaced fluid can damage the internal components. Any displaced fluid must be dried
up immediately.
17) In the event of failure/emergency, disconnect the mains supply by removing the plug from
the mains socket.
1.
Fill stainless steel tank with liquid; Plug the cleaner into grounded outlet; Powering on.
NOTE:
1. Do not run the cleaner continuously for more than one hour.
2. Do not pour water out until it’s cooling, Hot water will hurt you and damage the machine itself.
8) DO NOT touch the unit if the machine has fallen into water during operation.
2.
Time setting:
0-30 mins adjustable ( To spand long-life, please don't continuous use the ultrasonic cleaner for
more than one hours). The cleaning stops when the timer counts down to 0.
3.
Set temperature:
30-80
℃
adjustable.The heating function stops automatically when it reach the setting temperature.
4. After using, empty the tank and clean both the outside and inside of the cleaner with clean and dry
cloth for next use.
APPLICATIONS
