background image

-25- 

external temperature sensor, if connected. If not connected 

-- 

will be written instead. 
If there is an asterisk, for example 

*24,2 

before the number 

this indicates that the unit has sent a temperature trigged by 
this sensor. 

Tstat: 25 

Indicates the set temperature for the thermostat function. If 
thermostat not is activated the message is 

Tstat: OFF

.

 

SMS about power supply 

The SMS sent to alert about the power supply are as follows 
 

Content in SMS 

Meaning 

Charge battery! 

Is sent when voltage is dropping below 12 
Volt 

Battery empty! 

Is sent when voltage is dropping below 11 
Volt 

SMS showing the SIM card settings 

If you want to control the settings of the SIM card you can request an SMS that shows 
most of the SIM card settings. Send an SMS to the unit with the following content: 

ABCD#8*2# 

where ABCD is your personal PINCODE. 

You will immediately receive an SMS as below: 
 

Content 

Exlanation 

*Ontech 9030 

Asterisk (

*

) means alarm function is turned on 

Alarmrelay: 

Alarmrelay function; 

ON

 or 

OFF

 

Tempwatch: 

<

 indicates if the unit alarms when the temperature drops 

below

 set temperature. 

>

 indicates if the unit alarms when the temperature rises 

above

 set temperature. 

Temp sens: 

Indicates which temperature sensor that controls alarms 
and thermostat; 

 INT

=internal sensor, 

EXT

=den external 

sensor. 

Ver 

Shows software version. Useful when contacting support. 

Summary of Contents for GSM 9030





































Reviews: